blob: d250f1adaf08337f6c35dafe7efd46787fc63d25 [file] [log] [blame]
# Copyright (c) 2021 Argentum Systems Ltd.
# SPDX-License-Identifier: Apache-2.0
if SOC_SERIES_SAML21 || SOC_SERIES_SAMR34 || SOC_SERIES_SAMR35
config SOC_ATMEL_SAML_DEBUG_PAUSE
bool "Insert a pause at boot, to allow a debugger to attach"
default y
help
Issues have been observed while attempting to attach a debugger.
These can be mitigated by inserting a small delay during the early boot
sequence, before the system clock is configured.
If you ever intend to attach a debugger, say y.
If you are confident that you will never attach a debugger to the
resulting binary, or require the best possible boot time, say n.
config SOC_ATMEL_SAML_OSC32K
bool "Internal 32.768 kHz RC oscillator"
help
Eable the internal 32.768 kHz RC oscillator at startup.
This can then be selected as the main clock reference for the SOC.
config SOC_ATMEL_SAML_XOSC32K
bool "External 32.768 kHz clock source"
help
Enable the external 32.768 kHz cloud source at startup.
This can then be selected as the main clock reference for the SOC.
config SOC_ATMEL_SAML_XOSC32K_CRYSTAL
bool "External 32.768 kHz clock is a crystal oscillator"
depends on SOC_ATMEL_SAML_XOSC32K
default y
help
Enable the crystal oscillator (if disabled, expect a clock signal on
XIN32).
config SOC_ATMEL_SAML_OSC16M
bool "Internal 16 MHz RC oscillator"
help
Enable the internal 16 MHz RC oscillator at startup.
This can then be selected as the main clock reference for the SOC.
# NOTE: XOSC is not currently supported
choice
prompt "Main clock reference"
default SOC_ATMEL_SAML_OPENLOOP_AS_MAIN
help
Selects the clock that will be used for the DFLL48M's reference.
Main clocks, such as the CPU and AHB clocks will be derived from
DFLL48M configured for 48 MHz.
config SOC_ATMEL_SAML_OPENLOOP_AS_MAIN
bool "OPENLOOP"
help
Note, this mode can only be used with an LDO regulator.
config SOC_ATMEL_SAML_OSC32K_AS_MAIN
bool "OSC32K"
depends on SOC_ATMEL_SAML_OSC32K
config SOC_ATMEL_SAML_XOSC32K_AS_MAIN
bool "XOSC32K"
depends on SOC_ATMEL_SAML_XOSC32K
config SOC_ATMEL_SAML_OSC16M_AS_MAIN
bool "OSC16M"
depends on SOC_ATMEL_SAML_OSC16M
endchoice
config SOC_ATMEL_SAMR3X_RADIO_OFF_SETUP
bool "Configure LoRa radio pins if not in use"
default y if !LORA
depends on SOC_SERIES_SAMR34 || SOC_SERIES_SAMR35
help
As detailed in DS70005356C, LoRa radio SPI pins do not have pull-ups,
so when the radio is not in use, it's important that CS is kept high,
to avoid unexpected behavior and increased current consumption. To
further reduce power consumption, radio can be kept in reset state by
keeping nRST pin low. When enabling this option, both CS and nRST will
be configured high and low, respectively.
endif # SOC_SERIES_SAML21 || SOC_SERIES_SAMR34 || SOC_SERIES_SAMR35