blob: dd100b28865ea2cc9c12b4276c798c025b34ae3d [file] [log] [blame]
/*
* Copyright (c) 2022 Seco Spa
*
* SPDX-License-Identifier: Apache-2.0
*/
/dts-v1/;
#include <st/f3/stm32f302Xc.dtsi>
#include <st/f3/stm32f302v(b-c)tx-pinctrl.dtsi>
/ {
model = "SECO JUNO SBC-D23 board (STM32F302VCT6)";
compatible = "seco,stm32f3-d23";
chosen {
zephyr,console = &usart1;
zephyr,code-partition = &slot0_partition;
zephyr,shell-uart = &usart1;
zephyr,sram = &sram0;
zephyr,flash = &flash0;
zephyr,canbus = &can1;
};
leds {
compatible = "gpio-leds";
led_1: led_1 {
gpios = <&gpiod 8 GPIO_ACTIVE_HIGH>;
label = "LED-1";
};
led_2: led_2 {
gpios = <&gpiod 9 GPIO_ACTIVE_HIGH>;
label = "LED-2";
};
};
out_3p3v_pwr: 3p3v-out-pwr-ctrl {
compatible = "regulator-fixed";
regulator-name = "3p3v-out-pwr-ctrl";
enable-gpios = <&gpioe 7 GPIO_ACTIVE_HIGH>;
regulator-always-on;
regulator-boot-on;
status = "okay";
};
out_gpio_bufa_pwr: out-gpio-bufa-pwr-ctrl {
compatible = "regulator-fixed";
regulator-name = "out-gpio-bufa-pwr-ctrl";
enable-gpios = <&gpiof 2 GPIO_ACTIVE_LOW>;
regulator-boot-on;
status = "okay";
};
out_gpio_bufb_pwr: out-gpio-bufb-pwr-ctrl {
compatible = "regulator-fixed";
regulator-name = "out-gpio-bufb-pwr-ctrl";
enable-gpios = <&gpiof 4 GPIO_ACTIVE_LOW>;
regulator-boot-on;
status = "okay";
};
in_gpio_buf_pwr: in-gpio-buf-pwr-ctrl {
compatible = "regulator-fixed";
regulator-name = "in-gpio-buf-pwr-ctrl";
enable-gpios = <&gpiof 6 GPIO_ACTIVE_LOW>;
regulator-boot-on;
status = "okay";
};
transceiver0: can-phy0 {
compatible = "nxp,tja1040", "can-transceiver-gpio";
standby-gpios = <&gpiod 0 GPIO_ACTIVE_HIGH>;
max-bitrate = <1000000>;
#phy-cells = <0>;
};
aliases {
led0 = &led_1;
led1 = &led_2;
};
};
&clk_lsi {
status = "okay";
};
&clk_hse {
clock-frequency = <DT_FREQ_M(8)>;
status = "okay";
};
&pll {
prediv = <1>;
mul = <9>;
clocks = <&clk_hse>;
status = "okay";
};
&rcc {
clocks = <&pll>;
clock-frequency = <DT_FREQ_M(72)>;
ahb-prescaler = <1>;
apb1-prescaler = <2>;
apb2-prescaler = <1>;
status = "okay";
};
/* Debug Serial */
&usart1 {
pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>;
pinctrl-names = "default";
current-speed = <115200>;
status = "okay";
};
/* Modbus */
&usart2 {
pinctrl-0 = <&usart2_tx_pd5 &usart2_rx_pd6
&usart2_cts_pd3 &usart2_rts_pd4>;
pinctrl-names = "default";
current-speed = <115200>;
};
/* RS-485 */
&usart3 {
pinctrl-0 = <&usart3_tx_pc10 &usart3_rx_pc11
&usart3_rts_pd12>;
pinctrl-names = "default";
current-speed = <115200>;
};
&uart5 {
pinctrl-0 = <&uart5_tx_pc12 &uart5_rx_pd2>;
pinctrl-names = "default";
current-speed = <115200>;
};
&i2c1 {
pinctrl-0 = <&i2c1_scl_pb6 &i2c1_sda_pb7>;
pinctrl-names = "default";
clock-frequency = <I2C_BITRATE_FAST>;
status = "okay";
};
&i2c2 {
/* alternate config usart1 */
pinctrl-0 = <&i2c2_scl_pa9 &i2c2_sda_pa10>;
pinctrl-names = "default";
clock-frequency = <I2C_BITRATE_FAST>;
};
&spi1 {
pinctrl-0 = <&spi1_nss_pa4 &spi1_sck_pb3
&spi1_miso_pb4 &spi1_mosi_pb5>;
pinctrl-names = "default";
status = "okay";
};
&spi2 {
pinctrl-0 = <&spi2_nss_pb12 &spi2_sck_pb13
&spi2_miso_pb14 &spi2_mosi_pb15>;
pinctrl-names = "default";
status = "okay";
};
zephyr_udc0: &usb {
pinctrl-0 = <&usb_dm_pa11 &usb_dp_pa12>;
pinctrl-names = "default";
status = "okay";
};
&rtc {
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
<&rcc STM32_SRC_LSI RTC_SEL(2)>;
status = "okay";
};
&can1 {
pinctrl-0 = <&can_rx_pb8 &can_tx_pb9>;
pinctrl-names = "default";
bus-speed = <125000>;
phys = <&transceiver0>;
status = "okay";
};
&flash0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
boot_partition: partition@0 {
label = "mcuboot";
reg = <0x00000000 0x00010000>;
read-only;
};
/*
* The flash starting at 0x00010000 and ending at
* 0x0001ffff (sectors 16-31) is reserved for use
* by the application.
*/
slot0_partition: partition@20000 {
label = "image-0";
reg = <0x00020000 0x00008000>;
};
slot1_partition: partition@28000 {
label = "image-1";
reg = <0x00028000 0x00008000>;
};
storage_partition: partition@30000 {
label = "storage";
reg = <0x00030000 0x00002000>;
};
scratch_partition: partition@32000 {
label = "image-scratch";
reg = <0x00032000 0x00008000>;
};
};
};
&iwdg {
status = "okay";
};
&timers1 {
st,prescaler = <10000>;
status = "okay";
pwm1: pwm {
pinctrl-0 = <&tim1_ch1_pe9 &tim1_ch2n_pe10 &tim1_ch2_pe11
&tim1_ch3n_pe12 &tim1_ch3_pe13 &tim1_ch4_pe14>;
pinctrl-names = "default";
status = "okay";
};
};
&timers4 {
st,prescaler = <10000>;
status = "okay";
pwm4: pwm {
pinctrl-0 = <&tim4_ch2_pd13 &tim4_ch3_pd14 &tim4_ch4_pd15>;
pinctrl-names = "default";
status = "okay";
};
};