boards/riscv/icev_wireless/doc/index.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _icev_wireless:

 ICE-V Wireless
 ##############

 Overview
 ********

 The ICE-V Wireless is a combined ESP32C3 and iCE40 FPGA board.

 See the `ICE-V Wireless Github Project`_ for details.

 .. figure:: img/icev_wireless.jpg
    :align: center
    :alt: ICE-V Wireless

    ICE-V Wireless

 Hardware
 ********

 This board combines an Espressif ESP32-C3-MINI-1 (which includes 4MB of flash in the module) with a
 Lattice iCE40UP5k-SG48 FPGA to allow WiFi and Bluetooth control of the FPGA. ESP32 and FPGA I/O is
 mostly uncommitted except for the pins used for SPI communication between ESP32 and FPGA. Several
 of the ESP32C3 GPIO pins are available for additonal interfaces such as serial, ADC, I2C, etc.

 For details on ESP32-C3 hardware please refer to the following resources:

 * `ESP32-C3-MINI-1 Datasheet`_
 * `ESP32-C3 Datasheet`_
 * `ESP32-C3 Technical Reference Manual`_

 For details on iCE40 hardware please refer to the following resources:

 * `iCE40 UltraPlus Family Datasheet`_

 Supported Features
 ==================

 The ICE-V Wireless board configuration supports the following hardware
 features:

 +-----------+------------+------------------+
 | Interface | Controller | Driver/Component |
 +===========+============+==================+
 | PMP       | on-chip    | arch/riscv       |
 +-----------+------------+------------------+
 | INTMTRX   | on-chip    | intc_esp32c3     |
 +-----------+------------+------------------+
 | PINMUX    | on-chip    | pinctrl_esp32    |
 +-----------+------------+------------------+
 | USB UART  | on-chip    | serial_esp32_usb |
 +-----------+------------+------------------+
 | GPIO      | on-chip    | gpio_esp32       |
 +-----------+------------+------------------+
 | UART      | on-chip    | uart_esp32       |
 +-----------+------------+------------------+
 | I2C       | on-chip    | i2c_esp32        |
 +-----------+------------+------------------+
 | SPI       | on-chip    | spi_esp32_spim   |
 +-----------+------------+------------------+
 | ADC       | on-chip    |                  |
 +-----------+------------+------------------+

 Other hardware features have not been enabled yet for this board.

 Connections and IOs
 ===================

 The ICE-V Wireless provides 1 row of reference, ESP32-C3, and iCE40 signals
 brought out to J3, as well as 3 PMOD connectors for interfacing directly to
 the iCE40 FPGA. Note that several of the iCE40 pins brought out to the PMOD
 connectors are capable of operating as differential pairs.

 .. figure:: img/icev_wireless_back.jpg
    :align: center
    :alt: ICE-V Wireless (Back)

    ICE-V Wireless (Back)

 The J3 pins are 4V, 3.3V, NRST, GPIO2, GPIO3, GPIO8, GPIO9, GPIO10, GPIO20,
 GPIO21, FPGA_P34, and GND. Note that GPIO2 and GPIO3 may be configured for
 ADC operation.

 For PMOD details, please refer to the `PMOD Specification`_ and the image
 below.

 .. figure:: img/icev_wireless_pinout.jpg
    :align: center
    :alt: ICE-V Wireless Pinout

 Programming and Debugging
 *************************

 Programming and debugging for the ICE-V Wireless ESP32-C3 target is
 incredibly easy 🎉 following the steps below.

 Building and Flashing
 *********************

 ESP-IDF bootloader
 ==================

 The board is using the ESP-IDF bootloader as the default 2nd stage bootloader.
 It is build as a subproject at each application build. No further attention
 is expected from the user.

 MCUboot bootloader
 ==================

 User may choose to use MCUboot bootloader instead. In that case the bootloader
 must be build (and flash) at least once.

 There are two options to be used when building an application:

 1. Sysbuild
 2. Manual build

 .. note::

    User can select the MCUboot bootloader by adding the following line
    to the board default configuration file.
    ```
    CONFIG_BOOTLOADER_MCUBOOT=y
    ```

 Sysbuild
 ========

 The sysbuild makes possible to build and flash all necessary images needed to
 bootstrap the board with the EPS32 SoC.

 To build the sample application using sysbuild use the command:

 .. zephyr-app-commands::
    :tool: west
    :app: samples/hello_world
    :board: icev_wireless
    :goals: build
    :west-args: --sysbuild
    :compact:

 By default, the ESP32 sysbuild creates bootloader (MCUboot) and application
 images. But it can be configured to create other kind of images.

 Build directory structure created by sysbuild is different from traditional
 Zephyr build. Output is structured by the domain subdirectories:

 .. code-block::

   build/
   ├── hello_world
   │   └── zephyr
   │       ├── zephyr.elf
   │       └── zephyr.bin
   ├── mcuboot
   │    └── zephyr
   │       ├── zephyr.elf
   │       └── zephyr.bin
   └── domains.yaml

 .. note::

    With ``--sysbuild`` option the bootloader will be re-build and re-flash
    every time the pristine build is used.

 For more information about the system build please read the :ref:`sysbuild` documentation.

 Manual build
 ============

 During the development cycle, it is intended to build & flash as quickly possible.
 For that reason, images can be build one at a time using traditional build.

 The instructions following are relevant for both manual build and sysbuild.
 The only difference is the structure of the build directory.

 .. note::

    Remember that bootloader (MCUboot) needs to be flash at least once.

 For the :code:`Hello, world!` application, follow the instructions below.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: icev_wireless
    :goals: build flash

 Open the serial monitor using the following command:

 .. code-block:: console

    $ west espressif monitor

 After the board has automatically reset and booted, you should see the following
 message in the monitor:

 .. code-block:: console

    ***** Booting Zephyr OS vx.x.x-xxx-gxxxxxxxxxxxx *****
    Hello World! icev_wireless

 Debugging
 *********

 As with much custom hardware, the ESP32C3 modules require patches to
 OpenOCD that are not upstreamed. Espressif maintains their own fork of
 the project. The custom OpenOCD can be obtained by running the following extension:

 .. code-block:: console

    west espressif install

 .. note::

    By default, the OpenOCD will be downloaded and installed under $HOME/.espressif/tools/zephyr directory
    (%USERPROFILE%/.espressif/tools/zephyr on Windows).

 The Zephyr SDK uses a bundled version of OpenOCD by default. You can overwrite that behavior by adding the
 ``-DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>``
 parameter when building.

 Here is an example for building the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: icev_wireless
    :goals: build flash
    :gen-args: -DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>

 You can debug an application in the usual way. Here is an example for the
 :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: icev_wireless
    :maybe-skip-config:
    :goals: debug

 References
 **********

 .. _ICE-V Wireless Github Project:
    https://github.com/ICE-V-Wireless/ICE-V-Wireless

 .. _ESP32-C3-MINI-1 Datasheet:
    https://www.espressif.com/sites/default/files/documentation/esp32-c3-mini-1_datasheet_en.pdf

 .. _ESP32-C3 Datasheet:
    https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf

 .. _ESP32-C3 Technical Reference Manual:
    https://www.espressif.com/sites/default/files/documentation/esp32-c3_technical_reference_manual_en.pdf

 .. _iCE40 UltraPlus Family Datasheet:
    https://www.latticesemi.com/-/media/LatticeSemi/Documents/DataSheets/iCE/iCE40-UltraPlus-Family-Data-Sheet.ashx

 .. _PMOD Specification:
    https://digilent.com/reference/_media/reference/pmod/pmod-interface-specification-1_2_0.pdf
	.. _icev_wireless:

	ICE-V Wireless
	##############

	Overview
	********

	The ICE-V Wireless is a combined ESP32C3 and iCE40 FPGA board.

	See the `ICE-V Wireless Github Project`_ for details.

	.. figure:: img/icev_wireless.jpg
	:align: center
	:alt: ICE-V Wireless

	ICE-V Wireless

	Hardware
	********

	This board combines an Espressif ESP32-C3-MINI-1 (which includes 4MB of flash in the module) with a
	Lattice iCE40UP5k-SG48 FPGA to allow WiFi and Bluetooth control of the FPGA. ESP32 and FPGA I/O is
	mostly uncommitted except for the pins used for SPI communication between ESP32 and FPGA. Several
	of the ESP32C3 GPIO pins are available for additonal interfaces such as serial, ADC, I2C, etc.

	For details on ESP32-C3 hardware please refer to the following resources:

	* `ESP32-C3-MINI-1 Datasheet`_
	* `ESP32-C3 Datasheet`_
	* `ESP32-C3 Technical Reference Manual`_

	For details on iCE40 hardware please refer to the following resources:

	* `iCE40 UltraPlus Family Datasheet`_

	Supported Features
	==================

	The ICE-V Wireless board configuration supports the following hardware
	features:

	+-----------+------------+------------------+
	\| Interface \| Controller \| Driver/Component \|
	+===========+============+==================+
	\| PMP \| on-chip \| arch/riscv \|
	+-----------+------------+------------------+
	\| INTMTRX \| on-chip \| intc_esp32c3 \|
	+-----------+------------+------------------+
	\| PINMUX \| on-chip \| pinctrl_esp32 \|
	+-----------+------------+------------------+
	\| USB UART \| on-chip \| serial_esp32_usb \|
	+-----------+------------+------------------+
	\| GPIO \| on-chip \| gpio_esp32 \|
	+-----------+------------+------------------+
	\| UART \| on-chip \| uart_esp32 \|
	+-----------+------------+------------------+
	\| I2C \| on-chip \| i2c_esp32 \|
	+-----------+------------+------------------+
	\| SPI \| on-chip \| spi_esp32_spim \|
	+-----------+------------+------------------+
	\| ADC \| on-chip \| \|
	+-----------+------------+------------------+

	Other hardware features have not been enabled yet for this board.

	Connections and IOs
	===================

	The ICE-V Wireless provides 1 row of reference, ESP32-C3, and iCE40 signals
	brought out to J3, as well as 3 PMOD connectors for interfacing directly to
	the iCE40 FPGA. Note that several of the iCE40 pins brought out to the PMOD
	connectors are capable of operating as differential pairs.

	.. figure:: img/icev_wireless_back.jpg
	:align: center
	:alt: ICE-V Wireless (Back)

	ICE-V Wireless (Back)

	The J3 pins are 4V, 3.3V, NRST, GPIO2, GPIO3, GPIO8, GPIO9, GPIO10, GPIO20,
	GPIO21, FPGA_P34, and GND. Note that GPIO2 and GPIO3 may be configured for
	ADC operation.

	For PMOD details, please refer to the `PMOD Specification`_ and the image
	below.

	.. figure:: img/icev_wireless_pinout.jpg
	:align: center
	:alt: ICE-V Wireless Pinout

	Programming and Debugging
	*************************

	Programming and debugging for the ICE-V Wireless ESP32-C3 target is
	incredibly easy 🎉 following the steps below.

	Building and Flashing
	*********************

	ESP-IDF bootloader
	==================

	The board is using the ESP-IDF bootloader as the default 2nd stage bootloader.
	It is build as a subproject at each application build. No further attention
	is expected from the user.

	MCUboot bootloader
	==================

	User may choose to use MCUboot bootloader instead. In that case the bootloader
	must be build (and flash) at least once.

	There are two options to be used when building an application:

	1. Sysbuild
	2. Manual build

	.. note::

	User can select the MCUboot bootloader by adding the following line
	to the board default configuration file.
	```
	CONFIG_BOOTLOADER_MCUBOOT=y
	```

	Sysbuild
	========

	The sysbuild makes possible to build and flash all necessary images needed to
	bootstrap the board with the EPS32 SoC.

	To build the sample application using sysbuild use the command:

	.. zephyr-app-commands::
	:tool: west
	:app: samples/hello_world
	:board: icev_wireless
	:goals: build
	:west-args: --sysbuild
	:compact:

	By default, the ESP32 sysbuild creates bootloader (MCUboot) and application
	images. But it can be configured to create other kind of images.

	Build directory structure created by sysbuild is different from traditional
	Zephyr build. Output is structured by the domain subdirectories:

	.. code-block::

	build/
	├── hello_world
	│ └── zephyr
	│ ├── zephyr.elf
	│ └── zephyr.bin
	├── mcuboot
	│ └── zephyr
	│ ├── zephyr.elf
	│ └── zephyr.bin
	└── domains.yaml

	.. note::

	With ``--sysbuild`` option the bootloader will be re-build and re-flash
	every time the pristine build is used.

	For more information about the system build please read the :ref:`sysbuild` documentation.

	Manual build
	============

	During the development cycle, it is intended to build & flash as quickly possible.
	For that reason, images can be build one at a time using traditional build.

	The instructions following are relevant for both manual build and sysbuild.
	The only difference is the structure of the build directory.

	.. note::

	Remember that bootloader (MCUboot) needs to be flash at least once.

	For the :code:`Hello, world!` application, follow the instructions below.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: icev_wireless
	:goals: build flash

	Open the serial monitor using the following command:

	.. code-block:: console

	$ west espressif monitor

	After the board has automatically reset and booted, you should see the following
	message in the monitor:

	.. code-block:: console

	*** Booting Zephyr OS vx.x.x-xxx-gxxxxxxxxxxxx ***
	Hello World! icev_wireless

	Debugging
	*********

	As with much custom hardware, the ESP32C3 modules require patches to
	OpenOCD that are not upstreamed. Espressif maintains their own fork of
	the project. The custom OpenOCD can be obtained by running the following extension:

	.. code-block:: console

	west espressif install

	.. note::

	By default, the OpenOCD will be downloaded and installed under $HOME/.espressif/tools/zephyr directory
	(%USERPROFILE%/.espressif/tools/zephyr on Windows).

	The Zephyr SDK uses a bundled version of OpenOCD by default. You can overwrite that behavior by adding the
	``-DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>``
	parameter when building.

	Here is an example for building the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: icev_wireless
	:goals: build flash
	:gen-args: -DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>

	You can debug an application in the usual way. Here is an example for the
	:ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: icev_wireless
	:maybe-skip-config:
	:goals: debug

	References
	**********

	.. _ICE-V Wireless Github Project:
	https://github.com/ICE-V-Wireless/ICE-V-Wireless

	.. _ESP32-C3-MINI-1 Datasheet:
	https://www.espressif.com/sites/default/files/documentation/esp32-c3-mini-1_datasheet_en.pdf

	.. _ESP32-C3 Datasheet:
	https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf

	.. _ESP32-C3 Technical Reference Manual:
	https://www.espressif.com/sites/default/files/documentation/esp32-c3_technical_reference_manual_en.pdf

	.. _iCE40 UltraPlus Family Datasheet:
	https://www.latticesemi.com/-/media/LatticeSemi/Documents/DataSheets/iCE/iCE40-UltraPlus-Family-Data-Sheet.ashx

	.. _PMOD Specification:
	https://digilent.com/reference/_media/reference/pmod/pmod-interface-specification-1_2_0.pdf