blob: 205a830ef6574ac4dd6cda9990b1c1ed856b3b3c [file] [log] [blame]
/*
* Copyright (c) 2021 Seagate Technology LLC
*
* SPDX-License-Identifier: Apache-2.0
*/
/dts-v1/;
#include <st/f0/stm32f070Xb.dtsi>
#include <st/f0/stm32f070cbtx-pinctrl.dtsi>
#include <dt-bindings/led/led.h>
#include <dt-bindings/led/seagate_legend_b1414.h>
/ {
chosen {
zephyr,console = &usart1;
zephyr,shell-uart = &usart1;
zephyr,sram = &sram0;
zephyr,flash = &flash0;
};
aliases {
watchdog0 = &iwdg;
};
board_id: brd-id {
compatible = "gpio-keys";
brd_id0: brd_id_0 {
label = "BRD_ID_0";
gpios = <&gpioc 13 0>;
};
brd_id1: brd_id_1 {
label = "BRD_ID_1";
gpios = <&gpioc 14 0>;
};
brd_id2: brd_id_2 {
label = "BRD_ID_2";
gpios = <&gpioc 15 0>;
};
};
};
&usart1 {
pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>;
pinctrl-names = "default";
current-speed = <115200>;
status = "okay";
};
&i2c1 {
pinctrl-0 = <&i2c1_scl_pb6 &i2c1_sda_pb7>;
pinctrl-names = "default";
clock-frequency = <I2C_BITRATE_STANDARD>;
status = "okay";
};
&spi1 {
pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>;
pinctrl-names = "default";
dmas = <&dma1 3 0x20440>, <&dma1 2 0x20480>;
dma-names = "tx", "rx";
status = "okay";
led_strip_spi: b1414@0 {
compatible = "everlight,b1414", "worldsemi,ws2812-spi";
label = "B1414";
/* SPI */
reg = <0>; /* ignored, but necessary for SPI bindings */
spi-max-frequency = <SPI_FREQ>;
/* B1414 */
spi-one-frame = <ONE_FRAME>;
spi-zero-frame = <ZERO_FRAME>;
color-mapping = <LED_COLOR_ID_RED>,
<LED_COLOR_ID_GREEN>,
<LED_COLOR_ID_BLUE>;
reset-delay = <250>;
};
};
&spi2 {
pinctrl-0 = <&spi2_sck_pb13 &spi2_miso_pb14 &spi2_mosi_pb15>;
pinctrl-names = "default";
cs-gpios = <&gpiob 12 GPIO_ACTIVE_LOW>;
status = "okay";
spi_nor: spi_nor@0 {
status = "okay";
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <8000000>;
label = "SPI_FLASH_0";
size = <1048576>;
/*
* Main flash source
*
* Vendor : Puya
* Model : P25Q21H
* Total size : 256 KB
* Erase size : whole chip, 64 and 32 KB blocks, 4 KB sectors,
* 256 B pages
* Write size : up to 256 B (page size)
* Lifetime : 100K erase/program cycles on each sector/block
*/
jedec-id = [85 40 12];
/*
* Alternate flash source
*
* Vendor : Fudan
* Model : FM25F01B
* Total size : 128 KB
* Erase size : whole chip, 64 and 32 KB blocks, 4 KB sectors
* Write size : up to 256 B (page size)
* Lifetime : 100K erase/program cycles on each sector/block
*
* jedec-id = [a1 31 11];
*
* Model only found in first Jordan (2"5) EVT revision
*
* Vendor : Fudan
* Model : FM25F005
* Total size : 64 KB
* Erase size : whole chip, 64 and 32 KB blocks, 4 KB sectors
*
* jedec-id = [a1 31 10];
*/
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
product_info: partition@0 {
label = "product-info";
reg = <0x00000000 0x1000>;
};
led_das: partition@10000 {
label = "led-das";
reg = <0x00001000 0x0000f000>;
};
};
};
};
&spi_nor {
status = "okay";
};
&dma1 {
status = "okay";
};
&timers3 {
/*
* The maximum period needed on Legend devices for activity LED
* hardware blinking is 250ms (i.e. "error" fast blink at 4 Hz).
*
* We can use the following equation to compute the
* corresponding prescaler value:
*
* period_max = counter_size / cycles_per_second
*
* With:
*
* cycles_per_second = 48 MHz / (prescaler + 1)
* counter_size = 2^16
* period_max = 0.25
*
* Which gives:
*
* prescaler = 48 MHz * 0.25 / 2^16 + 1 = 182
*
* So any prescaler value above 182 is good for a 4 Hz hardware
* blinking. In addition the PWM frequency must be as high as
* possible to fool eyes and cameras with steady brightness
* levels.
*/
st,prescaler = <200>;
pwm3: pwm {
pinctrl-0 = <&tim3_ch3_pb0>;
pinctrl-names = "default";
status = "disabled";
};
};
&gpiod {
status = "disabled";
};
&gpiof {
status = "disabled";
};
&iwdg {
status = "okay";
};