| /* |
| * Copyright (c) 2019, NXP |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #include "lpcxpresso55s69-pinctrl.dtsi" |
| |
| / { |
| aliases{ |
| led0 = &red_led; |
| led1 = &green_led; |
| led2 = &blue_led; |
| spi-8 = &hs_lspi; |
| usart-0 = &flexcomm0; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| green_led: led_1 { |
| gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; |
| label = "User LD2"; |
| status = "disabled"; |
| }; |
| blue_led: led_2 { |
| gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; |
| label = "User LD3"; |
| status = "disabled"; |
| }; |
| red_led: led_3 { |
| gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; |
| label = "User LD4"; |
| status = "disabled"; |
| }; |
| }; |
| |
| mikrobus_header: mikrobus-connector { |
| compatible = "mikro-bus"; |
| #gpio-cells = <2>; |
| gpio-map-mask = <0xffffffff 0xffffffc0>; |
| gpio-map-pass-thru = <0 0x3f>; |
| gpio-map = <0 0 &gpio0 16 0>, /* AN */ |
| /* Not a GPIO*/ /* RST */ |
| <2 0 &gpio1 1 0>, /* CS */ |
| <3 0 &gpio1 2 0>, /* SCK */ |
| <4 0 &gpio1 3 0>, /* MISO */ |
| <5 0 &gpio0 26 0>, /* MOSI */ |
| /* +3.3V */ |
| /* GND */ |
| <6 0 &gpio1 5 0>, /* PWM */ |
| <7 0 &gpio1 18 0>, /* INT */ |
| <8 0 &gpio1 24 0>, /* RX */ |
| <9 0 &gpio0 27 0>, /* TX */ |
| <10 0 &gpio1 20 0>, /* SCL */ |
| <11 0 &gpio1 21 0>; /* SDA */ |
| /* +5V */ |
| /* GND */ |
| }; |
| |
| arduino_header: arduino-connector { |
| compatible = "arduino-header-r3"; |
| #gpio-cells = <2>; |
| gpio-map-mask = <0xffffffff 0xffffffc0>; |
| gpio-map-pass-thru = <0 0x3f>; |
| gpio-map = <0 0 &gpio0 16 0>, /* A0 */ |
| <1 0 &gpio0 23 0>, /* A1 */ |
| <2 0 &gpio0 0 0>, /* A2 */ |
| <3 0 &gpio1 31 0>, /* A3 */ |
| <4 0 &gpio0 13 0>, /* A4 */ |
| <5 0 &gpio0 14 0>, /* A5 */ |
| <6 0 &gpio1 24 0>, /* D0 */ |
| <7 0 &gpio0 27 0>, /* D1 */ |
| <8 0 &gpio0 15 0>, /* D2 */ |
| <9 0 &gpio1 6 0>, /* D3 */ |
| <10 0 &gpio1 7 0>, /* D4 */ |
| <11 0 &gpio1 4 0>, /* D5 */ |
| <12 0 &gpio1 10 0>, /* D6 */ |
| <13 0 &gpio1 9 0>, /* D7 */ |
| <14 0 &gpio1 8 0>, /* D8 */ |
| <15 0 &gpio1 5 0>, /* D9 */ |
| <16 0 &gpio1 1 0>, /* D10 */ |
| <17 0 &gpio0 26 0>, /* D11 */ |
| <18 0 &gpio1 3 0>, /* D12 */ |
| <19 0 &gpio1 2 0>, /* D13 */ |
| <20 0 &gpio1 21 0>, /* D14 */ |
| <21 0 &gpio1 20 0>; /* D15 */ |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| /* RAM split used by TFM */ |
| secure_ram: partition@20000000 { |
| label = "secure-memory"; |
| reg = <0x20000000 DT_SIZE_K(136)>; |
| }; |
| |
| non_secure_ram: partition@20022000 { |
| label = "non-secure-memory"; |
| reg = <0x20022000 DT_SIZE_K(136)>; |
| }; |
| }; |
| }; |
| |
| &flexcomm0 { |
| compatible = "nxp,lpc-usart"; |
| current-speed = <115200>; |
| }; |
| |
| &flash0 { |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| /* Please enable mcuboot's swap move, no scratch */ |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0x00008000>; |
| read-only; |
| }; |
| slot0_partition: partition@8000 { |
| label = "image-0"; |
| reg = <0x00008000 0x00028000>; |
| }; |
| slot1_partition: partition@30000 { |
| label = "image-1"; |
| reg = <0x00030000 0x00018000>; |
| }; |
| slot2_partition: partition@48000 { |
| label = "image-2"; |
| reg = <0x00048000 0x00028000>; |
| }; |
| slot3_partition: partition@70000 { |
| label = "image-3"; |
| reg = <0x00070000 0x00018000>; |
| }; |
| /* |
| * The flash starting at 0x88000 and ending at |
| * 0x949FF is reserved for the application. |
| */ |
| storage_partition: partition@88000 { |
| label = "storage"; |
| reg = <0x00088000 0x0000ca00>; |
| }; |
| }; |
| }; |
| |
| arduino_i2c: &flexcomm4 { |
| compatible = "nxp,lpc-i2c"; |
| clock-frequency = <I2C_BITRATE_STANDARD>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| mma8652fc@1d { |
| compatible = "nxp,fxos8700","nxp,mma8652fc"; |
| reg = <0x1d>; |
| label = "MMA8652FC"; |
| int1-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| arduino_serial: &flexcomm2 { |
| compatible = "nxp,lpc-usart"; |
| current-speed = <115200>; |
| }; |
| |
| arduino_spi: &hs_lspi { |
| }; |
| |
| arduino_gpio: &gpio1 { |
| }; |
| |
| mikrobus_spi: &hs_lspi { |
| }; |
| |
| &flexcomm0 { |
| pinctrl-0 = <&pinmux_flexcomm0_usart>; |
| pinctrl-names = "default"; |
| }; |
| |
| &flexcomm2 { |
| pinctrl-0 = <&pinmux_flexcomm2_usart>; |
| pinctrl-names = "default"; |
| }; |
| |
| &flexcomm4 { |
| pinctrl-0 = <&pinmux_flexcomm4_i2c>; |
| pinctrl-names = "default"; |
| }; |
| |
| &flexcomm6 { |
| pinctrl-0 = <&pinmux_flexcomm6_i2s>; |
| pinctrl-names = "default"; |
| }; |
| |
| &flexcomm7 { |
| pinctrl-0 = <&pinmux_flexcomm7_i2s>; |
| pinctrl-names = "default"; |
| }; |
| |
| &hs_lspi { |
| pinctrl-0 = <&pinmux_hs_lspi_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| &sc_timer { |
| pinctrl-0 = <&pinmux_sctimer_default>; |
| pinctrl-names = "default"; |
| }; |