| # nRF52840 PCA10090 board configuration |
| |
| # Copyright (c) 2018 Nordic Semiconductor ASA |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if BOARD_NRF52840_PCA10090 |
| |
| config BOARD_ENABLE_DCDC |
| bool "Enable DCDC mode" |
| select SOC_DCDC_NRF52X |
| default y |
| |
| choice |
| prompt "nRF9160 UART0 routing" |
| default BOARD_PCA10090_UART0_VCOM |
| |
| config BOARD_PCA10090_UART0_VCOM |
| bool "Route to VCOM0" |
| |
| config BOARD_PCA10090_UART0_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "nRF9160 UART1 routing" |
| default BOARD_PCA10090_UART1_VCOM |
| |
| config BOARD_PCA10090_UART1_VCOM |
| bool "Route to VCOM2" |
| |
| config BOARD_PCA10090_UART1_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "LED 1 routing" |
| default BOARD_PCA10090_LED0_PHY |
| |
| config BOARD_PCA10090_LED0_PHY |
| bool "Route to LED on the kit" |
| |
| config BOARD_PCA10090_LED0_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "LED 2 routing" |
| default BOARD_PCA10090_LED1_PHY |
| |
| config BOARD_PCA10090_LED1_PHY |
| bool "Route to LED on the kit" |
| |
| config BOARD_PCA10090_LED1_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "LED 3 routing" |
| default BOARD_PCA10090_LED2_PHY |
| |
| config BOARD_PCA10090_LED2_PHY |
| bool "Route to LED on the kit" |
| |
| config BOARD_PCA10090_LED2_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "LED 4 routing" |
| default BOARD_PCA10090_LED3_PHY |
| |
| config BOARD_PCA10090_LED3_PHY |
| bool "Route to LED on the kit" |
| |
| config BOARD_PCA10090_LED3_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "Button 1 routing" |
| default BOARD_PCA10090_BUTTON0_PHY |
| |
| config BOARD_PCA10090_BUTTON0_PHY |
| bool "Route to buttons on the kit" |
| |
| config BOARD_PCA10090_BUTTON0_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "Button 2 routing" |
| default BOARD_PCA10090_BUTTON1_PHY |
| |
| config BOARD_PCA10090_BUTTON1_PHY |
| bool "Route to buttons on the kit" |
| |
| config BOARD_PCA10090_BUTTON1_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "Switch 1 routing" |
| default BOARD_PCA10090_SWITCH0_PHY |
| |
| config BOARD_PCA10090_SWITCH0_PHY |
| bool "Route to switches on the kit" |
| |
| config BOARD_PCA10090_SWITCH0_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "Switch 2 routing" |
| default BOARD_PCA10090_SWITCH1_PHY |
| |
| config BOARD_PCA10090_SWITCH1_PHY |
| bool "Route to switches on the kit" |
| |
| config BOARD_PCA10090_SWITCH1_ARDUINO |
| bool "Route to Arduino pins" |
| |
| endchoice |
| |
| choice |
| prompt "Interface pins 0-2" |
| default BOARD_PCA10090_INTERFACE0_ARDUINO |
| |
| config BOARD_PCA10090_INTERFACE0_ARDUINO |
| bool "Route to Arduino pins" |
| help |
| Pin 0: nRF9160 P0.17 connects to A3 |
| Pin 1: nRF9160 P0.18 connects to A4 |
| Pin 2: nRF9160 P0.19 connects to A5 |
| |
| config BOARD_PCA10090_INTERFACE0_MCU |
| bool "Route to nRF52840" |
| help |
| This connects the following pins on the nRF9160 to pins on the nRF52840: |
| Pin 0: nRF9160 P0.17 connects to nRF52840 P0.17 |
| Pin 1: nRF9160 P0.18 connects to nRF52840 P0.20 |
| Pin 2: nRF9160 P0.19 connects to nRF52840 P0.15 |
| |
| endchoice |
| |
| choice |
| prompt "Interface pins 3-5" |
| default BOARD_PCA10090_INTERFACE1_TRACE |
| |
| config BOARD_PCA10090_INTERFACE1_TRACE |
| bool "Route to TRACE interface" |
| help |
| Pin 3: nRF9160 P0.21 connects to TRACECLK |
| Pin 4: nRF9160 P0.22 connects to TRACEDATA0 |
| Pin 5: nRF9160 P0.23 connects to TRACEDATA1 |
| |
| config BOARD_PCA10090_INTERFACE1_MCU |
| bool "Route to nRF52840" |
| help |
| Pin 3: nRF9160 P0.21 connects to nRF52840 P0.22 |
| Pin 4: nRF9160 P0.22 connects to nRF52840 P1.04 |
| Pin 5: nRF9160 P0.23 connects to nRF52840 P1.02 |
| |
| endchoice |
| |
| choice |
| prompt "Interface pins 6-8" |
| default BOARD_PCA10090_INTERFACE2_COEX |
| |
| config BOARD_PCA10090_INTERFACE2_COEX |
| bool "Route to COEX interface" |
| help |
| Pin 6: nRF9160 COEX0 connects to COEX0_PH |
| Pin 7: nRF9160 COEX1 connects to COEX1_PH |
| Pin 8: nRF9160 COEX2 connects to COEX2_PH |
| |
| config BOARD_PCA10090_INTERFACE2_MCU |
| bool "Route to nRF52840" |
| help |
| Pin 6: nRF9160 COEX0 connects to nRF52840 P1.13 |
| Pin 7: nRF9160 COEX1 connects to nRF52840 P1.11 |
| Pin 8: nRF9160 COEX2 connects to nRF52840 P1.15 |
| |
| endchoice |
| |
| config BOARD_PCA10090_NRF52840_RESET |
| bool "Enable GPIO reset line" |
| help |
| Let the nRF52840 be reset from the nRF9160 via a GPIO line. |
| The GPIO line may only be one of the first 6 MCU interface pins. |
| The line is active high. |
| |
| if BOARD_PCA10090_NRF52840_RESET |
| |
| choice |
| prompt "Pin used for reset" |
| |
| comment "nRF52840 pins" |
| |
| config BOARD_PCA10090_NRF52840_RESET_P0_17 |
| bool "P0.17" |
| depends on BOARD_PCA10090_INTERFACE0_MCU |
| help |
| Pin P0.17 on nRF52840, |
| connected to P0.17 on the nRF9160. |
| |
| config BOARD_PCA10090_NRF52840_RESET_P0_20 |
| bool "P0.20" |
| depends on BOARD_PCA10090_INTERFACE0_MCU |
| help |
| Pin P0.20 on nRF52840, |
| connected to P0.18 on the nRF9160. |
| |
| config BOARD_PCA10090_NRF52840_RESET_P0_15 |
| bool "P0.15" |
| depends on BOARD_PCA10090_INTERFACE0_MCU |
| help |
| Pin P0.15 on nRF52840, |
| connected to P0.19 on the nRF9160. |
| |
| config BOARD_PCA10090_NRF52840_RESET_P0_22 |
| bool "P0.22" |
| depends on BOARD_PCA10090_INTERFACE1_MCU |
| help |
| Pin P0.22 on nRF52840, |
| connected to P0.21 on the nRF9160. |
| |
| config BOARD_PCA10090_NRF52840_RESET_P1_04 |
| bool "P1.04" |
| depends on BOARD_PCA10090_INTERFACE1_MCU |
| help |
| Pin P1.04 on nRF52840, |
| connected to P0.22 on the nRF9160. |
| |
| config BOARD_PCA10090_NRF52840_RESET_P1_02 |
| bool "P1.02" |
| depends on BOARD_PCA10090_INTERFACE1_MCU |
| help |
| Pin P1.02 on nRF52840, |
| connected to P0.23 on the nRF9160. |
| |
| endchoice |
| |
| endif # BOARD_PCA10090_NRF52840_RESET |
| |
| module = BOARD_PCA10090 |
| module-str = Board Control |
| source "subsys/logging/Kconfig.template.log_config" |
| |
| endif # BOARD_NRF52840_PCA10090 |
