| # Bluetooth common configuration options |
| |
| # Copyright (c) 2017 Nordic Semiconductor ASA |
| # Copyright (c) 2016 Intel Corporation |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| config BT_HAS_HCI_VS |
| bool |
| help |
| This option is set by the Bluetooth controller to indicate support |
| for the Zephyr HCI Vendor-Specific Commands and Event. |
| |
| config BT_HCI_VS |
| bool "Zephyr HCI Vendor-Specific Commands" |
| depends on BT_HAS_HCI_VS |
| default y |
| help |
| Enable support for the Zephyr HCI Vendor-Specific Commands in the |
| Host and/or Controller. This enables Set Version Information, |
| Supported Commands, Supported Features vendor commands. |
| |
| config BT_HCI_VS_EXT |
| bool "Zephyr HCI Vendor-Specific Extensions" |
| depends on BT_HCI_VS |
| default y |
| help |
| Enable support for the Zephyr HCI Vendor-Specific Extensions in the |
| Host and/or Controller. This enables Write BD_ADDR, Read Build Info, |
| Read Static Addresses and Read Key Hierarchy Roots vendor commands. |
| |
| config BT_HCI_VS_EXT_DETECT |
| bool "Use heuristics to guess HCI vendor extensions support in advance" |
| depends on BT_HCI_VS_EXT && !BT_CTLR |
| default y if BOARD_QEMU_X86 || BOARD_QEMU_CORTEX_M3 || BOARD_NATIVE_POSIX |
| help |
| Use some heuristics to try to guess in advance whether the controller |
| supports the HCI vendor extensions in advance, in order to prevent |
| sending vendor commands to controller which may interpret them in |
| completely different ways. |
| |
| config BT_HCI_MESH_EXT |
| bool "Mesh HCI Command support" |
| depends on BT_BROADCASTER && BT_OBSERVER && !BT_LL_SW_SPLIT |
| help |
| Enable support for the Bluetooth Mesh HCI Commands. |
| |
| config BT_WAIT_NOP |
| bool "Wait for \"NOP\" Command Complete event during init" |
| help |
| Emit a Command Complete event from the Controller (and wait for it |
| from the Host) for the NOP opcode to indicate that the Controller is |
| ready to receive commands. |
| |
| config BT_RPA |
| bool |
| select TINYCRYPT |
| select TINYCRYPT_AES |
| |
| config BT_ASSERT |
| bool "Custom Bluetooth assert implementation" |
| default y |
| help |
| Use a custom Bluetooth assert implementation instead of the |
| kernel-wide __ASSERT(), which is enabled by CONFIG_ASSERT and is |
| disabled by default. |
| |
| if BT_ASSERT |
| |
| config BT_ASSERT_VERBOSE |
| bool "Print out an assert string when using BT_ASSERT" |
| default y |
| help |
| When CONFIG_BT_ASSERT is enabled, this option turns on printing the |
| cause of the assert to the console using printk(). |
| |
| config BT_ASSERT_PANIC |
| bool "Use k_panic() instead of k_oops()" |
| help |
| When CONFIG_BT_ASSERT is enabled, this option makes the code call |
| k_panic() instead of k_oops() when an assertion is triggered. |
| |
| endif # BT_ASSERT |
| |
| config BT_DEBUG |
| # Hidden option to make the conditions more intuitive |
| bool |
| |
| choice |
| prompt "Bluetooth debug type" |
| default BT_DEBUG_NONE |
| |
| config BT_DEBUG_NONE |
| bool "No debug log" |
| help |
| Select this to disable all Bluetooth debug logs. |
| |
| config BT_DEBUG_LOG |
| bool "Normal printf-style to console" |
| select BT_DEBUG |
| select LOG |
| help |
| This option enables Bluetooth debug going to standard |
| serial console. |
| |
| config BT_DEBUG_MONITOR |
| bool "Monitor protocol over UART" |
| select BT_DEBUG |
| select LOG |
| select CONSOLE_HAS_DRIVER |
| help |
| Use a custom logging protocol over the console UART |
| instead of plain-text output. Requires a special application |
| on the host side that can decode this protocol. Currently |
| the 'btmon' tool from BlueZ is capable of doing this. |
| |
| If the target board has two or more external UARTs it is |
| possible to keep using UART_CONSOLE together with this option, |
| however if there is only a single external UART then |
| UART_CONSOLE needs to be disabled (in which case printk/printf |
| will get encoded into the monitor protocol). |
| |
| endchoice |
| |
| if BT_DEBUG |
| |
| # Workaround for not being able to have commas in macro arguments |
| DT_CHOSEN_Z_BT_MON_UART := zephyr,bt-mon-uart |
| |
| config BT_MONITOR_ON_DEV_NAME |
| string "Device Name of Bluetooth monitor logging UART" |
| depends on BT_DEBUG_MONITOR |
| default "$(dt_chosen_label,$(DT_CHOSEN_Z_BT_MON_UART))" if HAS_DTS |
| default "UART_0" |
| help |
| This option specifies the name of UART device to be used |
| for the Bluetooth monitor logging. |
| |
| config BT_DEBUG_HCI_DRIVER |
| bool "Bluetooth HCI driver debug" |
| help |
| This option enables debug support for the active |
| Bluetooth HCI driver, including the Controller-side HCI layer |
| when included in the build. |
| |
| config BT_DEBUG_RPA |
| bool "Bluetooth Resolvable Private Address (RPA) debug" |
| depends on BT_RPA |
| help |
| This option enables debug support for the Bluetooth |
| Resolvable Private Address (RPA) generation and resolution. |
| |
| endif # BT_DEBUG |
