boards/lairdconnect/bl5340_dvk/Kconfig.defconfig

# BL5340-DVK board configuration

# Copyright (c) 2019-2020 Nordic Semiconductor ASA
# Copyright (c) 2021-2023 Laird Connectivity
# SPDX-License-Identifier: Apache-2.0

if BOARD_BL5340_DVK_NRF5340_CPUAPP || BOARD_BL5340_DVK_NRF5340_CPUAPP_NS

config I2C
	default GPIO || DAC

# Code Partition:
#
# For the secure version of the board the firmware is linked at the beginning
# of the flash, or into the code-partition defined in DT if it is intended to
# be loaded by MCUboot. If the secure firmware is to be combined with a non-
# secure image (TRUSTED_EXECUTION_SECURE=y), the secure FW image shall always
# be restricted to the size of its code partition.
#
# For the non-secure version of the board, the firmware
# must be linked into the code-partition (non-secure) defined in DT, regardless.
# Apply this configuration below by setting the Kconfig symbols used by
# the linker according to the information extracted from DT partitions.

# SRAM Partition:
#
# If the secure firmware is to be combined with a non-secure image
# (TRUSTED_EXECUTION_SECURE=y), the secure FW image SRAM shall always
# be restricted to the secure image SRAM partition (sram-secure-partition).
# Otherwise (if TRUSTED_EXECUTION_SECURE is not set) the whole zephyr,sram
# may be used by the image.
#
# For the non-secure version of the board, the firmware image SRAM is
# always restricted to the allocated non-secure SRAM partition.
#
# Workaround for not being able to have commas in macro arguments
DT_CHOSEN_Z_CODE_PARTITION := zephyr,code-partition
DT_CHOSEN_Z_SRAM_PARTITION := zephyr,sram-secure-partition

if BOARD_BL5340_DVK_NRF5340_CPUAPP && TRUSTED_EXECUTION_SECURE

config FLASH_LOAD_SIZE
	default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))

config SRAM_SIZE
	default $(dt_chosen_reg_size_int,$(DT_CHOSEN_Z_SRAM_PARTITION),0,K)

endif # BOARD_BL5340_DVK_NRF5340_CPUAPP && TRUSTED_EXECUTION_SECURE

if BOARD_BL5340_DVK_NRF5340_CPUAPP_NS

config FLASH_LOAD_OFFSET
	default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_PARTITION))

config FLASH_LOAD_SIZE
	default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))

endif # BOARD_BL5340_DVK_NRF5340_CPUAPP_NS

choice BT_HCI_BUS_TYPE
	default BT_HCI_IPC if BT
endchoice

config HEAP_MEM_POOL_ADD_SIZE_BOARD
	int
	default 4096 if BT_HCI_IPC

config BT_HCI_VS
	default y if BT

# 2.8" TFT Touch Shield for Arduino w/Capacitive Touch Screen Module
# is mounted to the DVK using standoffs.
# https://www.buydisplay.com/2-8-inch-tft-touch-shield-for-arduino-w-capacitive-touch-screen-module
if DISPLAY

config INPUT_FT5336_INTERRUPT
	default y

if LVGL

config LV_Z_VDB_SIZE
	default 64

config LV_Z_BITS_PER_PIXEL
	default 16

choice LV_COLOR_DEPTH
	default LV_COLOR_DEPTH_16
endchoice

config LV_COLOR_16_SWAP
	default y

config INPUT
	default y

endif # LVGL

endif # DISPLAY

endif # BOARD_BL5340_DVK_NRF5340_CPUAPP || BOARD_BL5340_DVK_NRF5340_CPUAPP_NS

config IPM_NRFX
	default IPM

config MBOX_NRFX_IPC
	default MBOX

if BOARD_BL5340_DVK_NRF5340_CPUNET

# BT_CTLR depends on BT. When BT is enabled we should default to also
# enabling the controller.
config BT_CTLR
	default y if BT

config BT_ECC
	default y if BT

endif # BOARD_BL5340_DVK_NRF5340_CPUNET