| .. _nuvoton_pfm_m467: |
| |
| NUVOTON NUMAKER PFM M467 |
| ######################## |
| |
| Overview |
| ******** |
| |
| The NuMaker PFM M467 is an Internet of Things (IoT) application focused platform |
| specially developed by Nuvoton. The PFM-M467 is based on the NuMicro® M467 |
| Ethernet series MCU with ARM® -Cortex®-M4F core. |
| |
| .. image:: ./pfm_m467.jpeg |
| :width: 720px |
| :align: center |
| :alt: PFM-M467 |
| |
| Features: |
| ========= |
| - 32-bit Arm Cortex®-M4 M467HJHAE MCU |
| - Core clock up to 200 MHz |
| - 1024 KB embedded Dual Bank Flash and 512 KB SRAM |
| - Ethernet (IP101GR) for network application |
| - USB 2.0 High-Speed OTG / Host / Device |
| - USB 1.1 Full-Speed OTG / Host / Device |
| - External SPI Flash (Winbond W25Q20) which can be regarded as ROM module |
| - MicroSD Card slot for T-Flash |
| - Arduino UNO compatible interface |
| - Three push-buttons: one is for reset and the other two are for user-defined |
| - Four LEDs: one is for power indication and the other three are for user-defined |
| - On-board NU-Link2 ICE debugger/programmer with SWD connector |
| |
| More information about the board can be found at the `PFM M467 User Manual`_. |
| |
| Supported Features |
| ================== |
| |
| * The on-board 12-MHz crystal allows the device to run at its maximum operating speed of 200MHz. |
| |
| The development board configuration supports the following hardware features: |
| |
| +-----------+------------+-----------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+=======================+ |
| | NVIC | on-chip | nested vectored | |
| | | | interrupt controller | |
| +-----------+------------+-----------------------+ |
| | SYSTICK | on-chip | system clock | |
| +-----------+------------+-----------------------+ |
| | UART | on-chip | serial port | |
| +-----------+------------+-----------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+-----------------------+ |
| |
| Other hardware features are not yet supported on Zephyr porting. |
| |
| More details about the supported peripherals are available in `M460 TRM`_ |
| Other hardware features are not currently supported by the Zephyr kernel. |
| |
| Building and Flashing |
| ********************* |
| Flashing |
| ======== |
| |
| Here is an example for the :ref:`hello_world` application. |
| |
| On board debugger Nu-link2 can emulate UART0 as a virtual COM port over usb, |
| To enable this, set ISW1 DIP switch 1-3 (TXD RXD VOM) to ON. |
| Connect the PFM M467 IoT to your host computer using the USB port, then |
| run a serial host program to connect with your board. For example: |
| |
| .. code-block:: console |
| |
| $ minicom -D /dev/ttyACM0 |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: numaker_pfm_m467 |
| :goals: flash |
| |
| Debugging |
| ========= |
| |
| Here is an example for the :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: numaker_pfm_m467 |
| :goals: debug |
| |
| Step through the application in your debugger. |
| |
| References |
| ********** |
| |
| .. _PFM M467 User Manual: |
| https://www.nuvoton.com/export/resource-files/UM_NuMaker-PFM-M467_User_Manual_EN_Rev1.01.pdf |
| .. _M460 TRM: |
| https://www.nuvoton.com/export/resource-files/TRM_M460_Series_EN_Rev1.01.pdf |
