| #CONFIG_INIT_STACKS=y # if set, lots of noise from mesh/adv.c: STACK_ANALYZE |
| CONFIG_MAIN_STACK_SIZE=512 |
| CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048 |
| |
| CONFIG_GPIO=y |
| |
| CONFIG_BT_SETTINGS=y |
| CONFIG_FLASH=y |
| CONFIG_FLASH_PAGE_LAYOUT=y |
| CONFIG_FLASH_MAP=y |
| CONFIG_NVS=y |
| CONFIG_SETTINGS=y |
| CONFIG_BT_MESH_RPL_STORE_TIMEOUT=600 |
| |
| CONFIG_BOOT_BANNER=y |
| |
| CONFIG_BT_OBSERVER=y |
| CONFIG_BT_BROADCASTER=y |
| CONFIG_BT_CTLR_DUP_FILTER_LEN=0 |
| CONFIG_BT_CTLR_LE_ENC=n |
| CONFIG_BT_CTLR_LE_PING=n |
| CONFIG_BT_DATA_LEN_UPDATE=n |
| CONFIG_BT_PHY_UPDATE=n |
| CONFIG_BT_CTLR_CHAN_SEL_2=n |
| CONFIG_BT_CTLR_MIN_USED_CHAN=n |
| CONFIG_BT_CTLR_ADV_EXT=n |
| CONFIG_BT_CTLR_PRIVACY=n |
| |
| CONFIG_BT_PERIPHERAL=y |
| |
| CONFIG_BT=y |
| CONFIG_BT_TINYCRYPT_ECC=y |
| CONFIG_BT_L2CAP_TX_BUF_COUNT=8 |
| |
| CONFIG_BT_MESH=y |
| CONFIG_BT_MESH_RELAY=y |
| CONFIG_BT_MESH_RELAY_ENABLED=n |
| CONFIG_BT_MESH_BEACON_ENABLED=n |
| CONFIG_BT_MESH_LOW_POWER=n |
| CONFIG_BT_MESH_FRIEND=n |
| CONFIG_BT_MESH_FRIEND_QUEUE_SIZE=16 |
| CONFIG_BT_MESH_ADV_BUF_COUNT=20 |
| CONFIG_BT_MESH_TX_SEG_MAX=6 |
| |
| CONFIG_BT_MESH_PB_GATT=y |
| CONFIG_BT_MESH_PB_ADV=y |
| CONFIG_BT_MESH_GATT_PROXY=y |
| CONFIG_BT_MESH_CFG_CLI=y |
| |
| #CONFIG_BT_MESH_LPN_SCAN_LATENCY=30 |
| #CONFIG_BT_MESH_LPN_RECV_DELAY=40 |
| #CONFIG_BT_MESH_LPN_POLL_TIMEOUT=300 |
| |
| CONFIG_BT_MESH_SUBNET_COUNT=2 |
| CONFIG_BT_MESH_APP_KEY_COUNT=2 |
| CONFIG_BT_MESH_MODEL_KEY_COUNT=2 |
| CONFIG_BT_MESH_MODEL_GROUP_COUNT=2 |
| CONFIG_BT_MESH_LABEL_COUNT=3 |
| |
| #CONFIG_BT_MESH_IV_UPDATE_TEST=y |
| |
| CONFIG_UART_CONSOLE=y |
| |
| # this outputs btmon formatted data to the serial port |
| #CONFIG_BT_DEBUG_MONITOR_UART=y |
| |
| CONFIG_BT_DEBUG_LOG=y |
| |
| CONFIG_BT_MESH_DEBUG=y |
| #CONFIG_BT_MESH_DEBUG_PROV=y |
| #CONFIG_BT_MESH_DEBUG_PROXY=y |
| #CONFIG_BT_MESH_DEBUG_BEACON=y |
| #CONFIG_BT_MESH_DEBUG_NET=y |
| #CONFIG_BT_MESH_DEBUG_TRANS=y |
| #CONFIG_BT_MESH_DEBUG_LOW_POWER=y |
| #CONFIG_BT_MESH_DEBUG_FRIEND=y |
| #CONFIG_BT_MESH_DEBUG_MODEL=y |
| #CONFIG_BT_MESH_DEBUG_ACCESS=y |
| #CONFIG_BT_MESH_DEBUG_CRYPTO=y |
| #CONFIG_BT_MESH_DEBUG_ADV=y |
| #CONFIG_BT_MESH_SELF_TEST=y |
| |
| #CONFIG_BT_HCI_VS_EXT=n |
| |
| #CONFIG_STACK_USAGE=y |
| |
| CONFIG_BT_RX_STACK_SIZE=4096 |
| |
| #CONFIG_BT_DEBUG_HCI_DRIVER=y |
| #CONFIG_BT_DEBUG_HCI_CORE=y |
| #CONFIG_BT_DEBUG_GATT=y |
| #CONFIG_BT_DEBUG_CONN=y |
| |
| CONFIG_BT_MAX_CONN=1 |
| CONFIG_BT_CTLR_RX_BUFFERS=6 |
| CONFIG_BT_BUF_ACL_TX_COUNT=4 |
| CONFIG_BT_BUF_CMD_TX_COUNT=4 |
| |
| CONFIG_BT_ATT_PREPARE_COUNT=2 |
| |
| #CONFIG_NET_BUF_SIMPLE_LOG=y |
| #CONFIG_NET_BUF_LOG=y |
| #CONFIG_BT_CTLR_DEBUG_PINS=y |
