blob: 79207aacceed17a6f81969c54c7ab18203a1ffc9 [file] [log] [blame]
/*
* Copyright (c) 2024 STMicroelectronics
*
* SPDX-License-Identifier: Apache-2.0
*/
/*
* **************************************************************************
* xSPI flash controller driver for stm32 serie with xSPI periherals
* This driver is based on the stm32Cube HAL XSPI driver
* with one xspi DTS NODE
* **************************************************************************
*/
#define DT_DRV_COMPAT st_stm32_xspi_nor
#include <errno.h>
#include <zephyr/kernel.h>
#include <soc.h>
#include <zephyr/drivers/pinctrl.h>
#include <zephyr/drivers/clock_control/stm32_clock_control.h>
#include <zephyr/drivers/clock_control.h>
#include <zephyr/drivers/flash.h>
#include <zephyr/dt-bindings/flash_controller/xspi.h>
#include <zephyr/drivers/gpio.h>
#include <zephyr/irq.h>
#include "spi_nor.h"
#include "jesd216.h"
#include <zephyr/logging/log.h>
LOG_MODULE_REGISTER(flash_stm32_xspi, CONFIG_FLASH_LOG_LEVEL);
#define STM32_XSPI_NODE DT_INST_PARENT(0)
#define DT_XSPI_IO_PORT_PROP_OR(prop, default_value) \
COND_CODE_1(DT_NODE_HAS_PROP(STM32_XSPI_NODE, prop), \
(_CONCAT(HAL_XSPIM_, DT_STRING_TOKEN(STM32_XSPI_NODE, prop))), \
((default_value)))
/* Get the base address of the flash from the DTS node */
#define STM32_XSPI_BASE_ADDRESS DT_INST_REG_ADDR(0)
#define STM32_XSPI_RESET_GPIO DT_INST_NODE_HAS_PROP(0, reset_gpios)
#define STM32_XSPI_DLYB_BYPASSED DT_PROP(STM32_XSPI_NODE, dlyb_bypass)
#define STM32_XSPI_USE_DMA DT_NODE_HAS_PROP(STM32_XSPI_NODE, dmas)
#if STM32_XSPI_USE_DMA
#include <zephyr/drivers/dma/dma_stm32.h>
#include <zephyr/drivers/dma.h>
#include <stm32_ll_dma.h>
#endif /* STM32_XSPI_USE_DMA */
#include "flash_stm32_xspi.h"
static inline void xspi_lock_thread(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
k_sem_take(&dev_data->sem, K_FOREVER);
}
static inline void xspi_unlock_thread(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
k_sem_give(&dev_data->sem);
}
static int xspi_send_cmd(const struct device *dev, XSPI_RegularCmdTypeDef *cmd)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
HAL_StatusTypeDef hal_ret;
LOG_DBG("Instruction 0x%x", cmd->Instruction);
dev_data->cmd_status = 0;
hal_ret = HAL_XSPI_Command(&dev_data->hxspi, cmd, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to send XSPI instruction", hal_ret);
return -EIO;
}
LOG_DBG("CCR 0x%x", dev_data->hxspi.Instance->CCR);
return dev_data->cmd_status;
}
static int xspi_read_access(const struct device *dev, XSPI_RegularCmdTypeDef *cmd,
uint8_t *data, const size_t size)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
HAL_StatusTypeDef hal_ret;
LOG_DBG("Instruction 0x%x", cmd->Instruction);
cmd->DataLength = size;
dev_data->cmd_status = 0;
hal_ret = HAL_XSPI_Command(&dev_data->hxspi, cmd, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to send XSPI instruction", hal_ret);
return -EIO;
}
#if STM32_XSPI_USE_DMA
hal_ret = HAL_XSPI_Receive_DMA(&dev_data->hxspi, data);
#else
hal_ret = HAL_XSPI_Receive_IT(&dev_data->hxspi, data);
#endif
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to read data", hal_ret);
return -EIO;
}
k_sem_take(&dev_data->sync, K_FOREVER);
return dev_data->cmd_status;
}
static int xspi_write_access(const struct device *dev, XSPI_RegularCmdTypeDef *cmd,
const uint8_t *data, const size_t size)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
HAL_StatusTypeDef hal_ret;
LOG_DBG("Instruction 0x%x", cmd->Instruction);
cmd->DataLength = size;
dev_data->cmd_status = 0;
/* in OPI/STR the 3-byte AddressWidth is not supported by the NOR flash */
if ((dev_cfg->data_mode == XSPI_OCTO_MODE) &&
(cmd->AddressWidth != HAL_XSPI_ADDRESS_32_BITS)) {
LOG_ERR("XSPI wr in OPI/STR mode is for 32bit address only");
return -EIO;
}
hal_ret = HAL_XSPI_Command(&dev_data->hxspi, cmd, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to send XSPI instruction", hal_ret);
return -EIO;
}
#if STM32_XSPI_USE_DMA
hal_ret = HAL_XSPI_Transmit_DMA(&dev_data->hxspi, (uint8_t *)data);
#else
hal_ret = HAL_XSPI_Transmit_IT(&dev_data->hxspi, (uint8_t *)data);
#endif
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to write data", hal_ret);
return -EIO;
}
k_sem_take(&dev_data->sync, K_FOREVER);
return dev_data->cmd_status;
}
/*
* Gives a XSPI_RegularCmdTypeDef with all parameters set
* except Instruction, Address, DummyCycles, NbData
*/
static XSPI_RegularCmdTypeDef xspi_prepare_cmd(const uint8_t transfer_mode,
const uint8_t transfer_rate)
{
XSPI_RegularCmdTypeDef cmd_tmp = {
.OperationType = HAL_XSPI_OPTYPE_COMMON_CFG,
.InstructionWidth = ((transfer_mode == XSPI_OCTO_MODE)
? HAL_XSPI_INSTRUCTION_16_BITS
: HAL_XSPI_INSTRUCTION_8_BITS),
.InstructionDTRMode = ((transfer_rate == XSPI_DTR_TRANSFER)
? HAL_XSPI_INSTRUCTION_DTR_ENABLE
: HAL_XSPI_INSTRUCTION_DTR_DISABLE),
.AddressDTRMode = ((transfer_rate == XSPI_DTR_TRANSFER)
? HAL_XSPI_ADDRESS_DTR_ENABLE
: HAL_XSPI_ADDRESS_DTR_DISABLE),
/* AddressWidth must be set to 32bits for init and mem config phase */
.AddressWidth = HAL_XSPI_ADDRESS_32_BITS,
.AlternateBytesMode = HAL_XSPI_ALT_BYTES_NONE,
.DataDTRMode = ((transfer_rate == XSPI_DTR_TRANSFER)
? HAL_XSPI_DATA_DTR_ENABLE
: HAL_XSPI_DATA_DTR_DISABLE),
.DQSMode = (transfer_rate == XSPI_DTR_TRANSFER)
? HAL_XSPI_DQS_ENABLE
: HAL_XSPI_DQS_DISABLE,
.SIOOMode = HAL_XSPI_SIOO_INST_EVERY_CMD,
};
switch (transfer_mode) {
case XSPI_OCTO_MODE: {
cmd_tmp.InstructionMode = HAL_XSPI_INSTRUCTION_8_LINES;
cmd_tmp.AddressMode = HAL_XSPI_ADDRESS_8_LINES;
cmd_tmp.DataMode = HAL_XSPI_DATA_8_LINES;
break;
}
case XSPI_QUAD_MODE: {
cmd_tmp.InstructionMode = HAL_XSPI_INSTRUCTION_4_LINES;
cmd_tmp.AddressMode = HAL_XSPI_ADDRESS_4_LINES;
cmd_tmp.DataMode = HAL_XSPI_DATA_4_LINES;
break;
}
case XSPI_DUAL_MODE: {
cmd_tmp.InstructionMode = HAL_XSPI_INSTRUCTION_2_LINES;
cmd_tmp.AddressMode = HAL_XSPI_ADDRESS_2_LINES;
cmd_tmp.DataMode = HAL_XSPI_DATA_2_LINES;
break;
}
default: {
cmd_tmp.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd_tmp.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
cmd_tmp.DataMode = HAL_XSPI_DATA_1_LINE;
break;
}
}
return cmd_tmp;
}
static uint32_t stm32_xspi_hal_address_size(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
if (dev_data->address_width == 4U) {
return HAL_XSPI_ADDRESS_32_BITS;
}
return HAL_XSPI_ADDRESS_24_BITS;
}
#if defined(CONFIG_FLASH_JESD216_API)
/*
* Read the JEDEC ID data from the external Flash at init
* and store in the jedec_id Table of the flash_stm32_xspi_data
* The JEDEC ID is not given by a DTS property
*/
static int stm32_xspi_read_jedec_id(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
/* This is a SPI/STR command to issue to the external Flash device */
XSPI_RegularCmdTypeDef cmd = xspi_prepare_cmd(XSPI_SPI_MODE, XSPI_STR_TRANSFER);
cmd.Instruction = JESD216_CMD_READ_ID;
cmd.AddressWidth = stm32_xspi_hal_address_size(dev);
cmd.AddressMode = HAL_XSPI_ADDRESS_NONE;
cmd.DataLength = JESD216_READ_ID_LEN; /* 3 bytes in the READ ID */
HAL_StatusTypeDef hal_ret;
hal_ret = HAL_XSPI_Command(&dev_data->hxspi, &cmd,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to send XSPI instruction", hal_ret);
return -EIO;
}
/* Place the received data directly into the jedec Table */
hal_ret = HAL_XSPI_Receive(&dev_data->hxspi, dev_data->jedec_id,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to read data", hal_ret);
return -EIO;
}
LOG_DBG("Jedec ID = [%02x %02x %02x]",
dev_data->jedec_id[0], dev_data->jedec_id[1], dev_data->jedec_id[2]);
dev_data->cmd_status = 0;
return 0;
}
/*
* Read Serial Flash ID :
* just gives the values received by the external Flash
*/
static int xspi_read_jedec_id(const struct device *dev, uint8_t *id)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
/* Take jedec Id values from the table (issued from the octoFlash) */
memcpy(id, dev_data->jedec_id, JESD216_READ_ID_LEN);
LOG_INF("Manuf ID = %02x Memory Type = %02x Memory Density = %02x",
id[0], id[1], id[2]);
return 0;
}
#endif /* CONFIG_FLASH_JESD216_API */
/*
* Read Serial Flash Discovery Parameter from the external Flash at init :
* perform a read access over SPI bus for SDFP (DataMode is already set)
* The SFDP table is not given by a DTS property
*/
static int stm32_xspi_read_sfdp(const struct device *dev, off_t addr,
void *data,
size_t size)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
XSPI_RegularCmdTypeDef cmd = xspi_prepare_cmd(dev_cfg->data_mode,
dev_cfg->data_rate);
if (dev_cfg->data_mode == XSPI_OCTO_MODE) {
cmd.Instruction = JESD216_OCMD_READ_SFDP;
cmd.DummyCycles = 20U;
cmd.AddressWidth = HAL_XSPI_ADDRESS_32_BITS;
} else {
cmd.Instruction = JESD216_CMD_READ_SFDP;
cmd.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd.DataMode = HAL_XSPI_DATA_1_LINE;
cmd.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
cmd.DummyCycles = 8U;
cmd.AddressWidth = HAL_XSPI_ADDRESS_24_BITS;
}
cmd.Address = addr;
cmd.DataLength = size;
HAL_StatusTypeDef hal_ret;
hal_ret = HAL_XSPI_Command(&dev_data->hxspi, &cmd, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to send XSPI instruction", hal_ret);
return -EIO;
}
hal_ret = HAL_XSPI_Receive(&dev_data->hxspi, (uint8_t *)data,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (hal_ret != HAL_OK) {
LOG_ERR("%d: Failed to read data", hal_ret);
return -EIO;
}
dev_data->cmd_status = 0;
return 0;
}
/*
* Read Serial Flash Discovery Parameter :
* perform a read access over SPI bus for SDFP (DataMode is already set)
*/
static int xspi_read_sfdp(const struct device *dev, off_t addr, void *data,
size_t size)
{
LOG_INF("Read SFDP from externalFlash");
/* Get the SFDP from the external Flash (no sfdp-bfp table in the DeviceTree) */
if (stm32_xspi_read_sfdp(dev, addr, data, size) == 0) {
/* If valid, then ignore any table from the DTS */
return 0;
}
LOG_INF("Error reading SFDP from external Flash and none in the DTS");
return -EINVAL;
}
static bool xspi_address_is_valid(const struct device *dev, off_t addr,
size_t size)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
size_t flash_size = dev_cfg->flash_size;
return (addr >= 0) && ((uint64_t)addr + (uint64_t)size <= flash_size);
}
static int stm32_xspi_wait_auto_polling(const struct device *dev,
XSPI_AutoPollingTypeDef *s_config, uint32_t timeout_ms)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
dev_data->cmd_status = 0;
if (HAL_XSPI_AutoPolling_IT(&dev_data->hxspi, s_config) != HAL_OK) {
LOG_ERR("XSPI AutoPoll failed");
return -EIO;
}
if (k_sem_take(&dev_data->sync, K_MSEC(timeout_ms)) != 0) {
LOG_ERR("XSPI AutoPoll wait failed");
HAL_XSPI_Abort(&dev_data->hxspi);
k_sem_reset(&dev_data->sync);
return -EIO;
}
/* HAL_XSPI_AutoPolling_IT enables transfer error interrupt which sets
* cmd_status.
*/
return dev_data->cmd_status;
}
/*
* This function Polls the WEL (write enable latch) bit to become to 0
* When the Chip Erase Cycle is completed, the Write Enable Latch (WEL) bit is cleared.
* in nor_mode SPI/OPI XSPI_SPI_MODE or XSPI_OCTO_MODE
* and nor_rate transfer STR/DTR XSPI_STR_TRANSFER or XSPI_DTR_TRANSFER
*/
static int stm32_xspi_mem_erased(const struct device *dev)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
uint8_t nor_mode = dev_cfg->data_mode;
uint8_t nor_rate = dev_cfg->data_rate;
XSPI_AutoPollingTypeDef s_config = {0};
XSPI_RegularCmdTypeDef s_command = xspi_prepare_cmd(nor_mode, nor_rate);
/* Configure automatic polling mode command to wait for memory ready */
if (nor_mode == XSPI_OCTO_MODE) {
s_command.Instruction = SPI_NOR_OCMD_RDSR;
s_command.DummyCycles = (nor_rate == XSPI_DTR_TRANSFER)
? SPI_NOR_DUMMY_REG_OCTAL_DTR
: SPI_NOR_DUMMY_REG_OCTAL;
} else {
s_command.Instruction = SPI_NOR_CMD_RDSR;
/* force 1-line InstructionMode for any non-OSPI transfer */
s_command.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
s_command.AddressMode = HAL_XSPI_ADDRESS_NONE;
/* force 1-line DataMode for any non-OSPI transfer */
s_command.DataMode = HAL_XSPI_DATA_1_LINE;
s_command.DummyCycles = 0;
}
s_command.DataLength = ((nor_rate == XSPI_DTR_TRANSFER) ? 2U : 1U);
s_command.Address = 0U;
/* Set the mask to 0x02 to mask all Status REG bits except WEL */
/* Set the match to 0x00 to check if the WEL bit is Reset */
s_config.MatchValue = SPI_NOR_WEL_MATCH;
s_config.MatchMask = SPI_NOR_WEL_MASK; /* Write Enable Latch */
s_config.MatchMode = HAL_XSPI_MATCH_MODE_AND;
s_config.IntervalTime = SPI_NOR_AUTO_POLLING_INTERVAL;
s_config.AutomaticStop = HAL_XSPI_AUTOMATIC_STOP_ENABLE;
if (HAL_XSPI_Command(&dev_data->hxspi, &s_command,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI AutoPoll command (WEL) failed");
return -EIO;
}
/* Start Automatic-Polling mode to wait until the memory is totally erased */
return stm32_xspi_wait_auto_polling(dev,
&s_config, STM32_XSPI_BULK_ERASE_MAX_TIME);
}
/*
* This function Polls the WIP(Write In Progress) bit to become to 0
* in nor_mode SPI/OPI XSPI_SPI_MODE or XSPI_OCTO_MODE
* and nor_rate transfer STR/DTR XSPI_STR_TRANSFER or XSPI_DTR_TRANSFER
*/
static int stm32_xspi_mem_ready(const struct device *dev, uint8_t nor_mode,
uint8_t nor_rate)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
XSPI_AutoPollingTypeDef s_config = {0};
XSPI_RegularCmdTypeDef s_command = xspi_prepare_cmd(nor_mode, nor_rate);
/* Configure automatic polling mode command to wait for memory ready */
if (nor_mode == XSPI_OCTO_MODE) {
s_command.Instruction = SPI_NOR_OCMD_RDSR;
s_command.DummyCycles = (nor_rate == XSPI_DTR_TRANSFER)
? SPI_NOR_DUMMY_REG_OCTAL_DTR
: SPI_NOR_DUMMY_REG_OCTAL;
} else {
s_command.Instruction = SPI_NOR_CMD_RDSR;
/* force 1-line InstructionMode for any non-OSPI transfer */
s_command.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
s_command.AddressMode = HAL_XSPI_ADDRESS_NONE;
/* force 1-line DataMode for any non-OSPI transfer */
s_command.DataMode = HAL_XSPI_DATA_1_LINE;
s_command.DummyCycles = 0;
}
s_command.DataLength = ((nor_rate == XSPI_DTR_TRANSFER) ? 2U : 1U);
s_command.Address = 0U;
/* Set the mask to 0x01 to mask all Status REG bits except WIP */
/* Set the match to 0x00 to check if the WIP bit is Reset */
s_config.MatchValue = SPI_NOR_MEM_RDY_MATCH;
s_config.MatchMask = SPI_NOR_MEM_RDY_MASK; /* Write in progress */
s_config.MatchMode = HAL_XSPI_MATCH_MODE_AND;
s_config.IntervalTime = SPI_NOR_AUTO_POLLING_INTERVAL;
s_config.AutomaticStop = HAL_XSPI_AUTOMATIC_STOP_ENABLE;
if (HAL_XSPI_Command(&dev_data->hxspi, &s_command,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI AutoPoll command failed");
return -EIO;
}
/* Start Automatic-Polling mode to wait until the memory is ready WIP=0 */
return stm32_xspi_wait_auto_polling(dev, &s_config, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
}
/* Enables writing to the memory sending a Write Enable and wait it is effective */
static int stm32_xspi_write_enable(const struct device *dev,
uint8_t nor_mode, uint8_t nor_rate)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
XSPI_AutoPollingTypeDef s_config = {0};
XSPI_RegularCmdTypeDef s_command = xspi_prepare_cmd(nor_mode, nor_rate);
/* Initialize the write enable command */
if (nor_mode == XSPI_OCTO_MODE) {
s_command.Instruction = SPI_NOR_OCMD_WREN;
} else {
s_command.Instruction = SPI_NOR_CMD_WREN;
/* force 1-line InstructionMode for any non-OSPI transfer */
s_command.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
}
s_command.AddressMode = HAL_XSPI_ADDRESS_NONE;
s_command.DataMode = HAL_XSPI_DATA_NONE;
s_command.DummyCycles = 0U;
if (HAL_XSPI_Command(&dev_data->hxspi, &s_command,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI flash write enable cmd failed");
return -EIO;
}
/* New command to Configure automatic polling mode to wait for write enabling */
if (nor_mode == XSPI_OCTO_MODE) {
s_command.Instruction = SPI_NOR_OCMD_RDSR;
s_command.AddressMode = HAL_XSPI_ADDRESS_8_LINES;
s_command.DataMode = HAL_XSPI_DATA_8_LINES;
s_command.DummyCycles = (nor_rate == XSPI_DTR_TRANSFER)
? SPI_NOR_DUMMY_REG_OCTAL_DTR
: SPI_NOR_DUMMY_REG_OCTAL;
} else {
s_command.Instruction = SPI_NOR_CMD_RDSR;
/* force 1-line DataMode for any non-OSPI transfer */
s_command.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
s_command.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
s_command.DataMode = HAL_XSPI_DATA_1_LINE;
s_command.DummyCycles = 0;
/* DummyCycles remains 0 */
}
s_command.DataLength = (nor_rate == XSPI_DTR_TRANSFER) ? 2U : 1U;
s_command.Address = 0U;
if (HAL_XSPI_Command(&dev_data->hxspi, &s_command,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI config auto polling cmd failed");
return -EIO;
}
s_config.MatchValue = SPI_NOR_WREN_MATCH;
s_config.MatchMask = SPI_NOR_WREN_MASK;
s_config.MatchMode = HAL_XSPI_MATCH_MODE_AND;
s_config.IntervalTime = SPI_NOR_AUTO_POLLING_INTERVAL;
s_config.AutomaticStop = HAL_XSPI_AUTOMATIC_STOP_ENABLE;
return stm32_xspi_wait_auto_polling(dev, &s_config, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
}
/* Write Flash configuration register 2 with new dummy cycles */
static int stm32_xspi_write_cfg2reg_dummy(XSPI_HandleTypeDef *hxspi,
uint8_t nor_mode, uint8_t nor_rate)
{
uint8_t transmit_data = SPI_NOR_CR2_DUMMY_CYCLES_66MHZ;
XSPI_RegularCmdTypeDef s_command = xspi_prepare_cmd(nor_mode, nor_rate);
/* Initialize the writing of configuration register 2 */
s_command.Instruction = (nor_mode == XSPI_SPI_MODE)
? SPI_NOR_CMD_WR_CFGREG2
: SPI_NOR_OCMD_WR_CFGREG2;
s_command.Address = SPI_NOR_REG2_ADDR3;
s_command.DummyCycles = 0U;
s_command.DataLength = (nor_mode == XSPI_SPI_MODE) ? 1U
: ((nor_rate == XSPI_DTR_TRANSFER) ? 2U : 1U);
if (HAL_XSPI_Command(hxspi, &s_command,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI transmit cmd");
return -EIO;
}
if (HAL_XSPI_Transmit(hxspi, &transmit_data,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI transmit ");
return -EIO;
}
return 0;
}
/* Write Flash configuration register 2 with new single or octal SPI protocol */
static int stm32_xspi_write_cfg2reg_io(XSPI_HandleTypeDef *hxspi,
uint8_t nor_mode, uint8_t nor_rate, uint8_t op_enable)
{
XSPI_RegularCmdTypeDef s_command = xspi_prepare_cmd(nor_mode, nor_rate);
/* Initialize the writing of configuration register 2 */
s_command.Instruction = (nor_mode == XSPI_SPI_MODE)
? SPI_NOR_CMD_WR_CFGREG2
: SPI_NOR_OCMD_WR_CFGREG2;
s_command.Address = SPI_NOR_REG2_ADDR1;
s_command.DummyCycles = 0U;
s_command.DataLength = (nor_mode == XSPI_SPI_MODE) ? 1U
: ((nor_rate == XSPI_DTR_TRANSFER) ? 2U : 1U);
if (HAL_XSPI_Command(hxspi, &s_command,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("Write Flash configuration reg2 failed");
return -EIO;
}
if (HAL_XSPI_Transmit(hxspi, &op_enable,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("Write Flash configuration reg2 failed");
return -EIO;
}
return 0;
}
/* Read Flash configuration register 2 with new single or octal SPI protocol */
static int stm32_xspi_read_cfg2reg(XSPI_HandleTypeDef *hxspi,
uint8_t nor_mode, uint8_t nor_rate, uint8_t *value)
{
XSPI_RegularCmdTypeDef s_command = xspi_prepare_cmd(nor_mode, nor_rate);
/* Initialize the writing of configuration register 2 */
s_command.Instruction = (nor_mode == XSPI_SPI_MODE)
? SPI_NOR_CMD_RD_CFGREG2
: SPI_NOR_OCMD_RD_CFGREG2;
s_command.Address = SPI_NOR_REG2_ADDR1;
s_command.DummyCycles = (nor_mode == XSPI_SPI_MODE)
? 0U
: ((nor_rate == XSPI_DTR_TRANSFER)
? SPI_NOR_DUMMY_REG_OCTAL_DTR
: SPI_NOR_DUMMY_REG_OCTAL);
s_command.DataLength = (nor_rate == XSPI_DTR_TRANSFER) ? 2U : 1U;
if (HAL_XSPI_Command(hxspi, &s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("Write Flash configuration reg2 failed");
return -EIO;
}
if (HAL_XSPI_Receive(hxspi, value, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("Write Flash configuration reg2 failed");
return -EIO;
}
return 0;
}
/* Set the NOR Flash to desired Interface mode : SPI/OSPI and STR/DTR according to the DTS */
static int stm32_xspi_config_mem(const struct device *dev)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
uint8_t reg[2];
/* Going to set the SPI mode and STR transfer rate : done */
if ((dev_cfg->data_mode != XSPI_OCTO_MODE)
&& (dev_cfg->data_rate == XSPI_STR_TRANSFER)) {
LOG_INF("OSPI flash config is SPI|DUAL|QUAD / STR");
return 0;
}
/* Going to set the XPI mode (STR or DTR transfer rate) */
LOG_DBG("XSPI configuring Octo SPI mode");
if (stm32_xspi_write_enable(dev,
XSPI_SPI_MODE, XSPI_STR_TRANSFER) != 0) {
LOG_ERR("OSPI write Enable failed");
return -EIO;
}
/* Write Configuration register 2 (with new dummy cycles) */
if (stm32_xspi_write_cfg2reg_dummy(&dev_data->hxspi,
XSPI_SPI_MODE, XSPI_STR_TRANSFER) != 0) {
LOG_ERR("XSPI write CFGR2 failed");
return -EIO;
}
if (stm32_xspi_mem_ready(dev,
XSPI_SPI_MODE, XSPI_STR_TRANSFER) != 0) {
LOG_ERR("XSPI autopolling failed");
return -EIO;
}
if (stm32_xspi_write_enable(dev,
XSPI_SPI_MODE, XSPI_STR_TRANSFER) != 0) {
LOG_ERR("XSPI write Enable 2 failed");
return -EIO;
}
/* Write Configuration register 2 (with Octal I/O SPI protocol : choose STR or DTR) */
uint8_t mode_enable = ((dev_cfg->data_rate == XSPI_DTR_TRANSFER)
? SPI_NOR_CR2_DTR_OPI_EN
: SPI_NOR_CR2_STR_OPI_EN);
if (stm32_xspi_write_cfg2reg_io(&dev_data->hxspi,
XSPI_SPI_MODE, XSPI_STR_TRANSFER, mode_enable) != 0) {
LOG_ERR("XSPI write CFGR2 failed");
return -EIO;
}
/* Wait that the configuration is effective and check that memory is ready */
k_busy_wait(STM32_XSPI_WRITE_REG_MAX_TIME * USEC_PER_MSEC);
/* Reconfigure the memory type of the peripheral */
dev_data->hxspi.Init.MemoryType = HAL_XSPI_MEMTYPE_MACRONIX;
dev_data->hxspi.Init.DelayHoldQuarterCycle = HAL_XSPI_DHQC_ENABLE;
if (HAL_XSPI_Init(&dev_data->hxspi) != HAL_OK) {
LOG_ERR("XSPI mem type MACRONIX failed");
return -EIO;
}
if (dev_cfg->data_rate == XSPI_STR_TRANSFER) {
if (stm32_xspi_mem_ready(dev,
XSPI_OCTO_MODE, XSPI_STR_TRANSFER) != 0) {
/* Check Flash busy ? */
LOG_ERR("XSPI flash busy failed");
return -EIO;
}
if (stm32_xspi_read_cfg2reg(&dev_data->hxspi,
XSPI_OCTO_MODE, XSPI_STR_TRANSFER, reg) != 0) {
/* Check the configuration has been correctly done on SPI_NOR_REG2_ADDR1 */
LOG_ERR("XSPI flash config read failed");
return -EIO;
}
LOG_INF("XSPI flash config is OCTO / STR");
}
if (dev_cfg->data_rate == XSPI_DTR_TRANSFER) {
if (stm32_xspi_mem_ready(dev,
XSPI_OCTO_MODE, XSPI_DTR_TRANSFER) != 0) {
/* Check Flash busy ? */
LOG_ERR("XSPI flash busy failed");
return -EIO;
}
LOG_INF("XSPI flash config is OCTO / DTR");
}
return 0;
}
/* gpio or send the different reset command to the NOR flash in SPI/OSPI and STR/DTR */
static int stm32_xspi_mem_reset(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
#if STM32_XSPI_RESET_GPIO
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
/* Generate RESETn pulse for the flash memory */
gpio_pin_configure_dt(&dev_cfg->reset, GPIO_OUTPUT_ACTIVE);
k_msleep(DT_INST_PROP(0, reset_gpios_duration));
gpio_pin_set_dt(&dev_cfg->reset, 0);
#else
/* Reset command sent sucessively for each mode SPI/OPS & STR/DTR */
XSPI_RegularCmdTypeDef s_command = {
.OperationType = HAL_XSPI_OPTYPE_COMMON_CFG,
.AddressMode = HAL_XSPI_ADDRESS_NONE,
.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE,
.InstructionDTRMode = HAL_XSPI_INSTRUCTION_DTR_DISABLE,
.Instruction = SPI_NOR_CMD_RESET_EN,
.InstructionWidth = HAL_XSPI_INSTRUCTION_8_BITS,
.AlternateBytesMode = HAL_XSPI_ALT_BYTES_NONE,
.DataLength = HAL_XSPI_DATA_NONE,
.DummyCycles = 0U,
.DQSMode = HAL_XSPI_DQS_DISABLE,
.SIOOMode = HAL_XSPI_SIOO_INST_EVERY_CMD,
};
/* Reset enable in SPI mode and STR transfer mode */
if (HAL_XSPI_Command(&dev_data->hxspi,
&s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI reset enable (SPI/STR) failed");
return -EIO;
}
/* Reset memory in SPI mode and STR transfer mode */
s_command.Instruction = SPI_NOR_CMD_RESET_MEM;
if (HAL_XSPI_Command(&dev_data->hxspi,
&s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI reset memory (SPI/STR) failed");
return -EIO;
}
/* Reset enable in OPI mode and STR transfer mode */
s_command.InstructionMode = HAL_XSPI_INSTRUCTION_8_LINES;
s_command.InstructionDTRMode = HAL_XSPI_INSTRUCTION_DTR_DISABLE;
s_command.Instruction = SPI_NOR_OCMD_RESET_EN;
s_command.InstructionWidth = HAL_XSPI_INSTRUCTION_16_BITS;
if (HAL_XSPI_Command(&dev_data->hxspi,
&s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI reset enable (OCTO/STR) failed");
return -EIO;
}
/* Reset memory in OPI mode and STR transfer mode */
s_command.Instruction = SPI_NOR_OCMD_RESET_MEM;
if (HAL_XSPI_Command(&dev_data->hxspi,
&s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI reset memory (OCTO/STR) failed");
return -EIO;
}
/* Reset enable in OPI mode and DTR transfer mode */
s_command.InstructionDTRMode = HAL_XSPI_INSTRUCTION_DTR_ENABLE;
s_command.Instruction = SPI_NOR_OCMD_RESET_EN;
if (HAL_XSPI_Command(&dev_data->hxspi,
&s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI reset enable (OCTO/DTR) failed");
return -EIO;
}
/* Reset memory in OPI mode and DTR transfer mode */
s_command.Instruction = SPI_NOR_OCMD_RESET_MEM;
if (HAL_XSPI_Command(&dev_data->hxspi,
&s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI reset memory (OCTO/DTR) failed");
return -EIO;
}
#endif /* STM32_XSPI_RESET_GPIO */
/* Wait after SWreset CMD, in case SWReset occurred during erase operation */
k_busy_wait(STM32_XSPI_RESET_MAX_TIME * USEC_PER_MSEC);
return 0;
}
#ifdef CONFIG_STM32_MEMMAP
/* Function to configure the octoflash in MemoryMapped mode */
static int stm32_xspi_set_memorymap(const struct device *dev)
{
HAL_StatusTypeDef ret;
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
XSPI_RegularCmdTypeDef s_command = {0}; /* Non-zero values disturb the command */
XSPI_MemoryMappedTypeDef s_MemMappedCfg;
/* Configure octoflash in MemoryMapped mode */
if ((dev_cfg->data_mode == XSPI_SPI_MODE) &&
(stm32_xspi_hal_address_size(dev) == HAL_XSPI_ADDRESS_24_BITS)) {
/* OPI mode and 3-bytes address size not supported by memory */
LOG_ERR("XSPI_SPI_MODE in 3Bytes addressing is not supported");
return -EIO;
}
/* Initialize the read command */
s_command.OperationType = HAL_XSPI_OPTYPE_READ_CFG;
s_command.InstructionMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? ((dev_cfg->data_mode == XSPI_SPI_MODE)
? HAL_XSPI_INSTRUCTION_1_LINE
: HAL_XSPI_INSTRUCTION_8_LINES)
: HAL_XSPI_INSTRUCTION_8_LINES;
s_command.InstructionDTRMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? HAL_XSPI_INSTRUCTION_DTR_DISABLE
: HAL_XSPI_INSTRUCTION_DTR_ENABLE;
s_command.InstructionWidth = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? ((dev_cfg->data_mode == XSPI_SPI_MODE)
? HAL_XSPI_INSTRUCTION_8_BITS
: HAL_XSPI_INSTRUCTION_16_BITS)
: HAL_XSPI_INSTRUCTION_16_BITS;
s_command.Instruction = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? ((dev_cfg->data_mode == XSPI_SPI_MODE)
? ((stm32_xspi_hal_address_size(dev) ==
HAL_XSPI_ADDRESS_24_BITS)
? SPI_NOR_CMD_READ_FAST
: SPI_NOR_CMD_READ_FAST_4B)
: dev_data->read_opcode)
: SPI_NOR_OCMD_DTR_RD;
s_command.AddressMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? ((dev_cfg->data_mode == XSPI_SPI_MODE)
? HAL_XSPI_ADDRESS_1_LINE
: HAL_XSPI_ADDRESS_8_LINES)
: HAL_XSPI_ADDRESS_8_LINES;
s_command.AddressDTRMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? HAL_XSPI_ADDRESS_DTR_DISABLE
: HAL_XSPI_ADDRESS_DTR_ENABLE;
s_command.AddressWidth = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? stm32_xspi_hal_address_size(dev)
: HAL_XSPI_ADDRESS_32_BITS;
s_command.DataMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? ((dev_cfg->data_mode == XSPI_SPI_MODE)
? HAL_XSPI_DATA_1_LINE
: HAL_XSPI_DATA_8_LINES)
: HAL_XSPI_DATA_8_LINES;
s_command.DataDTRMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? HAL_XSPI_DATA_DTR_DISABLE
: HAL_XSPI_DATA_DTR_ENABLE;
s_command.DummyCycles = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? ((dev_cfg->data_mode == XSPI_SPI_MODE)
? SPI_NOR_DUMMY_RD
: SPI_NOR_DUMMY_RD_OCTAL)
: SPI_NOR_DUMMY_RD_OCTAL_DTR;
s_command.DQSMode = (dev_cfg->data_rate == XSPI_STR_TRANSFER)
? HAL_XSPI_DQS_DISABLE
: HAL_XSPI_DQS_ENABLE;
#ifdef XSPI_CCR_SIOO
s_command.SIOOMode = HAL_XSPI_SIOO_INST_EVERY_CMD;
#endif /* XSPI_CCR_SIOO */
ret = HAL_XSPI_Command(&dev_data->hxspi, &s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (ret != HAL_OK) {
LOG_ERR("%d: Failed to set memory map", ret);
return -EIO;
}
/* Initialize the program command */
s_command.OperationType = HAL_XSPI_OPTYPE_WRITE_CFG;
if (dev_cfg->data_rate == XSPI_STR_TRANSFER) {
s_command.Instruction = (dev_cfg->data_mode == XSPI_SPI_MODE)
? ((stm32_xspi_hal_address_size(dev) ==
HAL_XSPI_ADDRESS_24_BITS)
? SPI_NOR_CMD_PP
: SPI_NOR_CMD_PP_4B)
: SPI_NOR_OCMD_PAGE_PRG;
} else {
s_command.Instruction = SPI_NOR_OCMD_PAGE_PRG;
}
s_command.DQSMode = HAL_XSPI_DQS_DISABLE;
ret = HAL_XSPI_Command(&dev_data->hxspi, &s_command, HAL_XSPI_TIMEOUT_DEFAULT_VALUE);
if (ret != HAL_OK) {
LOG_ERR("%d: Failed to set memory mapped", ret);
return -EIO;
}
/* Enable the memory-mapping */
s_MemMappedCfg.TimeOutActivation = HAL_XSPI_TIMEOUT_COUNTER_DISABLE;
ret = HAL_XSPI_MemoryMapped(&dev_data->hxspi, &s_MemMappedCfg);
if (ret != HAL_OK) {
LOG_ERR("%d: Failed to enable memory mapped", ret);
return -EIO;
}
LOG_DBG("MemoryMap mode enabled");
return 0;
}
/* Function to return true if the octoflash is in MemoryMapped else false */
static bool stm32_xspi_is_memorymap(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
return ((READ_BIT(dev_data->hxspi.Instance->CR,
XSPI_CR_FMODE) == XSPI_CR_FMODE) ?
true : false);
}
static int stm32_xspi_abort(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
if (HAL_XSPI_Abort(&dev_data->hxspi) != HAL_OK) {
LOG_ERR("XSPI abort failed");
return -EIO;
}
return 0;
}
#endif /* CONFIG_STM32_MEMMAP */
/*
* Function to erase the flash : chip or sector with possible OCTO/SPI and STR/DTR
* to erase the complete chip (using dedicated command) :
* set size >= flash size
* set addr = 0
*/
static int flash_stm32_xspi_erase(const struct device *dev, off_t addr,
size_t size)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
int ret = 0;
/* Ignore zero size erase */
if (size == 0) {
return 0;
}
/* Maximise erase size : means the complete chip */
if (size > dev_cfg->flash_size) {
size = dev_cfg->flash_size;
}
if (!xspi_address_is_valid(dev, addr, size)) {
LOG_ERR("Error: address or size exceeds expected values: "
"addr 0x%lx, size %zu", (long)addr, size);
return -EINVAL;
}
if (((size % SPI_NOR_SECTOR_SIZE) != 0) && (size < dev_cfg->flash_size)) {
LOG_ERR("Error: wrong sector size 0x%x", size);
return -ENOTSUP;
}
xspi_lock_thread(dev);
#ifdef CONFIG_STM32_MEMMAP
if (stm32_xspi_is_memorymap(dev)) {
/* Abort ongoing transfer to force CS high/BUSY deasserted */
ret = stm32_xspi_abort(dev);
if (ret != 0) {
LOG_ERR("Failed to abort memory-mapped access before erase");
goto erase_end;
}
}
#endif
XSPI_RegularCmdTypeDef cmd_erase = {
.OperationType = HAL_XSPI_OPTYPE_COMMON_CFG,
.AlternateBytesMode = HAL_XSPI_ALT_BYTES_NONE,
.DataMode = HAL_XSPI_DATA_NONE,
.DummyCycles = 0U,
.DQSMode = HAL_XSPI_DQS_DISABLE,
.SIOOMode = HAL_XSPI_SIOO_INST_EVERY_CMD,
};
if (stm32_xspi_mem_ready(dev,
dev_cfg->data_mode, dev_cfg->data_rate) != 0) {
LOG_ERR("Erase failed : flash busy");
goto erase_end;
}
cmd_erase.InstructionMode = (dev_cfg->data_mode == XSPI_OCTO_MODE)
? HAL_XSPI_INSTRUCTION_8_LINES
: HAL_XSPI_INSTRUCTION_1_LINE;
cmd_erase.InstructionDTRMode = (dev_cfg->data_rate == XSPI_DTR_TRANSFER)
? HAL_XSPI_INSTRUCTION_DTR_ENABLE
: HAL_XSPI_INSTRUCTION_DTR_DISABLE;
cmd_erase.InstructionWidth = (dev_cfg->data_mode == XSPI_OCTO_MODE)
? HAL_XSPI_INSTRUCTION_16_BITS
: HAL_XSPI_INSTRUCTION_8_BITS;
while ((size > 0) && (ret == 0)) {
ret = stm32_xspi_write_enable(dev,
dev_cfg->data_mode, dev_cfg->data_rate);
if (ret != 0) {
LOG_ERR("Erase failed : write enable");
break;
}
if (size == dev_cfg->flash_size) {
/* Chip erase */
LOG_DBG("Chip Erase");
cmd_erase.Address = 0;
cmd_erase.Instruction = (dev_cfg->data_mode == XSPI_OCTO_MODE)
? SPI_NOR_OCMD_BULKE
: SPI_NOR_CMD_BULKE;
cmd_erase.AddressMode = HAL_XSPI_ADDRESS_NONE;
/* Full chip erase (Bulk) command */
xspi_send_cmd(dev, &cmd_erase);
size -= dev_cfg->flash_size;
/* Chip (Bulk) erase started, wait until WEL becomes 0 */
ret = stm32_xspi_mem_erased(dev);
if (ret != 0) {
LOG_ERR("Chip Erase failed");
break;
}
} else {
/* Sector or Block erase depending on the size */
LOG_DBG("Sector/Block Erase");
cmd_erase.AddressMode =
(dev_cfg->data_mode == XSPI_OCTO_MODE)
? HAL_XSPI_ADDRESS_8_LINES
: HAL_XSPI_ADDRESS_1_LINE;
cmd_erase.AddressDTRMode =
(dev_cfg->data_rate == XSPI_DTR_TRANSFER)
? HAL_XSPI_ADDRESS_DTR_ENABLE
: HAL_XSPI_ADDRESS_DTR_DISABLE;
cmd_erase.AddressWidth = stm32_xspi_hal_address_size(dev);
cmd_erase.Address = addr;
const struct jesd216_erase_type *erase_types =
dev_data->erase_types;
const struct jesd216_erase_type *bet = NULL;
for (uint8_t ei = 0;
ei < JESD216_NUM_ERASE_TYPES; ++ei) {
const struct jesd216_erase_type *etp =
&erase_types[ei];
if ((etp->exp != 0)
&& SPI_NOR_IS_ALIGNED(addr, etp->exp)
&& (size >= BIT(etp->exp))
&& ((bet == NULL)
|| (etp->exp > bet->exp))) {
bet = etp;
cmd_erase.Instruction = bet->cmd;
} else if (bet == NULL) {
/* Use the default sector erase cmd */
if (dev_cfg->data_mode == XSPI_OCTO_MODE) {
cmd_erase.Instruction = SPI_NOR_OCMD_SE;
} else {
cmd_erase.Instruction =
(stm32_xspi_hal_address_size(dev) ==
HAL_XSPI_ADDRESS_32_BITS)
? SPI_NOR_CMD_SE_4B
: SPI_NOR_CMD_SE;
}
}
/* Avoid using wrong erase type,
* if zero entries are found in erase_types
*/
bet = NULL;
}
LOG_DBG("Sector/Block Erase addr 0x%x, asize 0x%x amode 0x%x instr 0x%x",
cmd_erase.Address, cmd_erase.AddressWidth,
cmd_erase.AddressMode, cmd_erase.Instruction);
xspi_send_cmd(dev, &cmd_erase);
if (bet != NULL) {
addr += BIT(bet->exp);
size -= BIT(bet->exp);
} else {
addr += SPI_NOR_SECTOR_SIZE;
size -= SPI_NOR_SECTOR_SIZE;
}
ret = stm32_xspi_mem_ready(dev, dev_cfg->data_mode,
dev_cfg->data_rate);
}
}
/* Ends the erase operation */
erase_end:
xspi_unlock_thread(dev);
return ret;
}
/* Function to read the flash with possible OCTO/SPI and STR/DTR */
static int flash_stm32_xspi_read(const struct device *dev, off_t addr,
void *data, size_t size)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
int ret;
if (!xspi_address_is_valid(dev, addr, size)) {
LOG_ERR("Error: address or size exceeds expected values: "
"addr 0x%lx, size %zu", (long)addr, size);
return -EINVAL;
}
/* Ignore zero size read */
if (size == 0) {
return 0;
}
#ifdef CONFIG_STM32_MEMMAP
ARG_UNUSED(dev_cfg);
ARG_UNUSED(dev_data);
xspi_lock_thread(dev);
/* Do reads through memory-mapping instead of indirect */
if (!stm32_xspi_is_memorymap(dev)) {
ret = stm32_xspi_set_memorymap(dev);
if (ret != 0) {
LOG_ERR("READ: failed to set memory mapped");
goto read_end;
}
}
__ASSERT_NO_MSG(stm32_xspi_is_memorymap(dev));
uintptr_t mmap_addr = STM32_XSPI_BASE_ADDRESS + addr;
LOG_DBG("Memory-mapped read from 0x%08lx, len %zu", mmap_addr, size);
memcpy(data, (void *)mmap_addr, size);
ret = 0;
goto read_end;
#else
XSPI_RegularCmdTypeDef cmd = xspi_prepare_cmd(dev_cfg->data_mode, dev_cfg->data_rate);
if (dev_cfg->data_mode != XSPI_OCTO_MODE) {
switch (dev_data->read_mode) {
case JESD216_MODE_112: {
cmd.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
cmd.DataMode = HAL_XSPI_DATA_2_LINES;
break;
}
case JESD216_MODE_122: {
cmd.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd.AddressMode = HAL_XSPI_ADDRESS_2_LINES;
cmd.DataMode = HAL_XSPI_DATA_2_LINES;
break;
}
case JESD216_MODE_114: {
cmd.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
cmd.DataMode = HAL_XSPI_DATA_4_LINES;
break;
}
case JESD216_MODE_144: {
cmd.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd.AddressMode = HAL_XSPI_ADDRESS_4_LINES;
cmd.DataMode = HAL_XSPI_DATA_4_LINES;
break;
}
default:
/* use the mode from ospi_prepare_cmd */
break;
}
}
/* Instruction and DummyCycles are set below */
cmd.Address = addr; /* AddressSize is 32bits in OPSI mode */
cmd.AddressWidth = stm32_xspi_hal_address_size(dev);
/* DataSize is set by the read cmd */
/* Configure other parameters */
if (dev_cfg->data_rate == XSPI_DTR_TRANSFER) {
/* DTR transfer rate (==> Octal mode) */
cmd.Instruction = SPI_NOR_OCMD_DTR_RD;
cmd.DummyCycles = SPI_NOR_DUMMY_RD_OCTAL_DTR;
} else {
/* STR transfer rate */
if (dev_cfg->data_mode == XSPI_OCTO_MODE) {
/* OPI and STR */
cmd.Instruction = SPI_NOR_OCMD_RD;
cmd.DummyCycles = SPI_NOR_DUMMY_RD_OCTAL;
} else {
/* use SFDP:BFP read instruction */
cmd.Instruction = dev_data->read_opcode;
cmd.DummyCycles = dev_data->read_dummy;
/* in SPI and STR : expecting SPI_NOR_CMD_READ_FAST_4B */
}
}
LOG_DBG("XSPI: read %zu data at 0x%lx",
size,
(long)(STM32_XSPI_BASE_ADDRESS + addr));
xspi_lock_thread(dev);
ret = xspi_read_access(dev, &cmd, data, size);
goto read_end;
#endif
read_end:
xspi_unlock_thread(dev);
return ret;
}
/* Function to write the flash (page program) : with possible OCTO/SPI and STR/DTR */
static int flash_stm32_xspi_write(const struct device *dev, off_t addr,
const void *data, size_t size)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
size_t to_write;
int ret = 0;
if (!xspi_address_is_valid(dev, addr, size)) {
LOG_ERR("Error: address or size exceeds expected values: "
"addr 0x%lx, size %zu", (long)addr, size);
return -EINVAL;
}
/* Ignore zero size write */
if (size == 0) {
return 0;
}
xspi_lock_thread(dev);
#ifdef CONFIG_STM32_MEMMAP
ARG_UNUSED(dev_data);
if (stm32_xspi_is_memorymap(dev)) {
/* Abort ongoing transfer to force CS high/BUSY deasserted */
ret = stm32_xspi_abort(dev);
if (ret != 0) {
LOG_ERR("Failed to abort memory-mapped access before write");
goto write_end;
}
}
#endif
/* page program for STR or DTR mode */
XSPI_RegularCmdTypeDef cmd_pp = xspi_prepare_cmd(dev_cfg->data_mode, dev_cfg->data_rate);
/* using 32bits address also in SPI/STR mode */
cmd_pp.Instruction = dev_data->write_opcode;
if (dev_cfg->data_mode != XSPI_OCTO_MODE) {
switch (cmd_pp.Instruction) {
case SPI_NOR_CMD_PP_4B:
__fallthrough;
case SPI_NOR_CMD_PP: {
cmd_pp.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd_pp.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
cmd_pp.DataMode = HAL_XSPI_DATA_1_LINE;
break;
}
case SPI_NOR_CMD_PP_1_1_4_4B:
__fallthrough;
case SPI_NOR_CMD_PP_1_1_4: {
cmd_pp.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd_pp.AddressMode = HAL_XSPI_ADDRESS_1_LINE;
cmd_pp.DataMode = HAL_XSPI_DATA_4_LINES;
break;
}
case SPI_NOR_CMD_PP_1_4_4_4B:
__fallthrough;
case SPI_NOR_CMD_PP_1_4_4: {
cmd_pp.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE;
cmd_pp.AddressMode = HAL_XSPI_ADDRESS_4_LINES;
cmd_pp.DataMode = HAL_XSPI_DATA_4_LINES;
break;
}
default:
/* use the mode from ospi_prepare_cmd */
break;
}
}
cmd_pp.Address = addr;
cmd_pp.AddressWidth = stm32_xspi_hal_address_size(dev);
cmd_pp.DummyCycles = 0U;
LOG_DBG("XSPI: write %zu data at 0x%lx",
size,
(long)(STM32_XSPI_BASE_ADDRESS + addr));
ret = stm32_xspi_mem_ready(dev,
dev_cfg->data_mode, dev_cfg->data_rate);
if (ret != 0) {
LOG_ERR("XSPI: write not ready");
goto write_end;
}
while ((size > 0) && (ret == 0)) {
to_write = size;
ret = stm32_xspi_write_enable(dev,
dev_cfg->data_mode, dev_cfg->data_rate);
if (ret != 0) {
LOG_ERR("XSPI: write not enabled");
break;
}
/* Don't write more than a page. */
if (to_write >= SPI_NOR_PAGE_SIZE) {
to_write = SPI_NOR_PAGE_SIZE;
}
/* Don't write across a page boundary */
if (((addr + to_write - 1U) / SPI_NOR_PAGE_SIZE)
!= (addr / SPI_NOR_PAGE_SIZE)) {
to_write = SPI_NOR_PAGE_SIZE -
(addr % SPI_NOR_PAGE_SIZE);
}
cmd_pp.Address = addr;
ret = xspi_write_access(dev, &cmd_pp, data, to_write);
if (ret != 0) {
LOG_ERR("XSPI: write not access");
break;
}
size -= to_write;
data = (const uint8_t *)data + to_write;
addr += to_write;
/* Configure automatic polling mode to wait for end of program */
ret = stm32_xspi_mem_ready(dev,
dev_cfg->data_mode, dev_cfg->data_rate);
if (ret != 0) {
LOG_ERR("XSPI: write PP not ready");
break;
}
}
/* Ends the write operation */
write_end:
xspi_unlock_thread(dev);
return ret;
}
static const struct flash_parameters flash_stm32_xspi_parameters = {
.write_block_size = 1,
.erase_value = 0xff
};
static const struct flash_parameters *
flash_stm32_xspi_get_parameters(const struct device *dev)
{
ARG_UNUSED(dev);
return &flash_stm32_xspi_parameters;
}
static void flash_stm32_xspi_isr(const struct device *dev)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
HAL_XSPI_IRQHandler(&dev_data->hxspi);
}
#if !defined(CONFIG_SOC_SERIES_STM32H7X)
/* weak function required for HAL compilation */
__weak HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef *hdma)
{
return HAL_OK;
}
/* weak function required for HAL compilation */
__weak HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma)
{
return HAL_OK;
}
#endif /* !CONFIG_SOC_SERIES_STM32H7X */
/* This function is executed in the interrupt context */
#if STM32_XSPI_USE_DMA
static void xspi_dma_callback(const struct device *dev, void *arg,
uint32_t channel, int status)
{
DMA_HandleTypeDef *hdma = arg;
ARG_UNUSED(dev);
if (status < 0) {
LOG_ERR("DMA callback error with channel %d.", channel);
}
HAL_DMA_IRQHandler(hdma);
}
#endif
/*
* Transfer Error callback.
*/
void HAL_XSPI_ErrorCallback(XSPI_HandleTypeDef *hxspi)
{
struct flash_stm32_xspi_data *dev_data =
CONTAINER_OF(hxspi, struct flash_stm32_xspi_data, hxspi);
LOG_DBG("Error cb");
dev_data->cmd_status = -EIO;
k_sem_give(&dev_data->sync);
}
/*
* Command completed callback.
*/
void HAL_XSPI_CmdCpltCallback(XSPI_HandleTypeDef *hxspi)
{
struct flash_stm32_xspi_data *dev_data =
CONTAINER_OF(hxspi, struct flash_stm32_xspi_data, hxspi);
LOG_DBG("Cmd Cplt cb");
k_sem_give(&dev_data->sync);
}
/*
* Rx Transfer completed callback.
*/
void HAL_XSPI_RxCpltCallback(XSPI_HandleTypeDef *hxspi)
{
struct flash_stm32_xspi_data *dev_data =
CONTAINER_OF(hxspi, struct flash_stm32_xspi_data, hxspi);
LOG_DBG("Rx Cplt cb");
k_sem_give(&dev_data->sync);
}
/*
* Tx Transfer completed callback.
*/
void HAL_XSPI_TxCpltCallback(XSPI_HandleTypeDef *hxspi)
{
struct flash_stm32_xspi_data *dev_data =
CONTAINER_OF(hxspi, struct flash_stm32_xspi_data, hxspi);
LOG_DBG("Tx Cplt cb");
k_sem_give(&dev_data->sync);
}
/*
* Status Match callback.
*/
void HAL_XSPI_StatusMatchCallback(XSPI_HandleTypeDef *hxspi)
{
struct flash_stm32_xspi_data *dev_data =
CONTAINER_OF(hxspi, struct flash_stm32_xspi_data, hxspi);
LOG_DBG("Status Match cb");
k_sem_give(&dev_data->sync);
}
/*
* Timeout callback.
*/
void HAL_XSPI_TimeOutCallback(XSPI_HandleTypeDef *hxspi)
{
struct flash_stm32_xspi_data *dev_data =
CONTAINER_OF(hxspi, struct flash_stm32_xspi_data, hxspi);
LOG_DBG("Timeout cb");
dev_data->cmd_status = -EIO;
k_sem_give(&dev_data->sync);
}
#if defined(CONFIG_FLASH_PAGE_LAYOUT)
static void flash_stm32_xspi_pages_layout(const struct device *dev,
const struct flash_pages_layout **layout,
size_t *layout_size)
{
struct flash_stm32_xspi_data *dev_data = dev->data;
*layout = &dev_data->layout;
*layout_size = 1;
}
#endif
static const struct flash_driver_api flash_stm32_xspi_driver_api = {
.read = flash_stm32_xspi_read,
.write = flash_stm32_xspi_write,
.erase = flash_stm32_xspi_erase,
.get_parameters = flash_stm32_xspi_get_parameters,
#if defined(CONFIG_FLASH_PAGE_LAYOUT)
.page_layout = flash_stm32_xspi_pages_layout,
#endif
#if defined(CONFIG_FLASH_JESD216_API)
.sfdp_read = xspi_read_sfdp,
.read_jedec_id = xspi_read_jedec_id,
#endif /* CONFIG_FLASH_JESD216_API */
};
#if defined(CONFIG_FLASH_PAGE_LAYOUT)
static int setup_pages_layout(const struct device *dev)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *data = dev->data;
const size_t flash_size = dev_cfg->flash_size;
uint32_t layout_page_size = data->page_size;
uint8_t value = 0;
int rv = 0;
/* Find the smallest erase size. */
for (size_t i = 0; i < ARRAY_SIZE(data->erase_types); ++i) {
const struct jesd216_erase_type *etp = &data->erase_types[i];
if ((etp->cmd != 0)
&& ((value == 0) || (etp->exp < value))) {
value = etp->exp;
}
}
uint32_t erase_size = BIT(value);
if (erase_size == 0) {
erase_size = SPI_NOR_SECTOR_SIZE;
}
/* We need layout page size to be compatible with erase size */
if ((layout_page_size % erase_size) != 0) {
LOG_DBG("layout page %u not compatible with erase size %u",
layout_page_size, erase_size);
LOG_DBG("erase size will be used as layout page size");
layout_page_size = erase_size;
}
/* Warn but accept layout page sizes that leave inaccessible
* space.
*/
if ((flash_size % layout_page_size) != 0) {
LOG_DBG("layout page %u wastes space with device size %zu",
layout_page_size, flash_size);
}
data->layout.pages_size = layout_page_size;
data->layout.pages_count = flash_size / layout_page_size;
LOG_DBG("layout %u x %u By pages", data->layout.pages_count,
data->layout.pages_size);
return rv;
}
#endif /* CONFIG_FLASH_PAGE_LAYOUT */
static int stm32_xspi_read_status_register(const struct device *dev, uint8_t reg_num, uint8_t *reg)
{
XSPI_RegularCmdTypeDef s_command = {
.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE,
.DataMode = HAL_XSPI_DATA_1_LINE,
};
switch (reg_num) {
case 1U:
s_command.Instruction = SPI_NOR_CMD_RDSR;
break;
case 2U:
s_command.Instruction = SPI_NOR_CMD_RDSR2;
break;
case 3U:
s_command.Instruction = SPI_NOR_CMD_RDSR3;
break;
default:
return -EINVAL;
}
return xspi_read_access(dev, &s_command, reg, sizeof(*reg));
}
static int stm32_xspi_write_status_register(const struct device *dev, uint8_t reg_num, uint8_t reg)
{
struct flash_stm32_xspi_data *data = dev->data;
XSPI_RegularCmdTypeDef s_command = {
.Instruction = SPI_NOR_CMD_WRSR,
.InstructionMode = HAL_XSPI_INSTRUCTION_1_LINE,
.DataMode = HAL_XSPI_DATA_1_LINE
};
size_t size;
uint8_t regs[4] = { 0 };
uint8_t *regs_p;
int ret;
if (reg_num == 1U) {
size = 1U;
regs[0] = reg;
regs_p = &regs[0];
/* 1 byte write clears SR2, write SR2 as well */
if (data->qer_type == JESD216_DW15_QER_S2B1v1) {
ret = stm32_xspi_read_status_register(dev, 2, &regs[1]);
if (ret < 0) {
return ret;
}
size = 2U;
}
} else if (reg_num == 2U) {
s_command.Instruction = SPI_NOR_CMD_WRSR2;
size = 1U;
regs[1] = reg;
regs_p = &regs[1];
/* if SR2 write needs SR1 */
if ((data->qer_type == JESD216_DW15_QER_VAL_S2B1v1) ||
(data->qer_type == JESD216_DW15_QER_VAL_S2B1v4) ||
(data->qer_type == JESD216_DW15_QER_VAL_S2B1v5)) {
ret = stm32_xspi_read_status_register(dev, 1, &regs[0]);
if (ret < 0) {
return ret;
}
s_command.Instruction = SPI_NOR_CMD_WRSR;
size = 2U;
regs_p = &regs[0];
}
} else if (reg_num == 3U) {
s_command.Instruction = SPI_NOR_CMD_WRSR3;
size = 1U;
regs[2] = reg;
regs_p = &regs[2];
} else {
return -EINVAL;
}
return xspi_write_access(dev, &s_command, regs_p, size);
}
static int stm32_xspi_enable_qe(const struct device *dev)
{
struct flash_stm32_xspi_data *data = dev->data;
uint8_t qe_reg_num;
uint8_t qe_bit;
uint8_t reg;
int ret;
switch (data->qer_type) {
case JESD216_DW15_QER_NONE:
/* no QE bit, device detects reads based on opcode */
return 0;
case JESD216_DW15_QER_S1B6:
qe_reg_num = 1U;
qe_bit = BIT(6U);
break;
case JESD216_DW15_QER_S2B7:
qe_reg_num = 2U;
qe_bit = BIT(7U);
break;
case JESD216_DW15_QER_S2B1v1:
__fallthrough;
case JESD216_DW15_QER_S2B1v4:
__fallthrough;
case JESD216_DW15_QER_S2B1v5:
__fallthrough;
case JESD216_DW15_QER_S2B1v6:
qe_reg_num = 2U;
qe_bit = BIT(1U);
break;
default:
return -ENOTSUP;
}
ret = stm32_xspi_read_status_register(dev, qe_reg_num, &reg);
if (ret < 0) {
return ret;
}
/* exit early if QE bit is already set */
if ((reg & qe_bit) != 0U) {
return 0;
}
ret = stm32_xspi_write_enable(dev, XSPI_SPI_MODE, XSPI_STR_TRANSFER);
if (ret < 0) {
return ret;
}
reg |= qe_bit;
ret = stm32_xspi_write_status_register(dev, qe_reg_num, reg);
if (ret < 0) {
return ret;
}
ret = stm32_xspi_mem_ready(dev, XSPI_SPI_MODE, XSPI_STR_TRANSFER);
if (ret < 0) {
return ret;
}
/* validate that QE bit is set */
ret = stm32_xspi_read_status_register(dev, qe_reg_num, &reg);
if (ret < 0) {
return ret;
}
if ((reg & qe_bit) == 0U) {
LOG_ERR("Status Register %u [0x%02x] not set", qe_reg_num, reg);
ret = -EIO;
}
return ret;
}
static void spi_nor_process_bfp_addrbytes(const struct device *dev,
const uint8_t jesd216_bfp_addrbytes)
{
struct flash_stm32_xspi_data *data = dev->data;
if ((jesd216_bfp_addrbytes == JESD216_SFDP_BFP_DW1_ADDRBYTES_VAL_4B) ||
(jesd216_bfp_addrbytes == JESD216_SFDP_BFP_DW1_ADDRBYTES_VAL_3B4B)) {
data->address_width = 4U;
} else {
data->address_width = 3U;
}
}
static inline uint8_t spi_nor_convert_read_to_4b(const uint8_t opcode)
{
switch (opcode) {
case SPI_NOR_CMD_READ:
return SPI_NOR_CMD_READ_4B;
case SPI_NOR_CMD_DREAD:
return SPI_NOR_CMD_DREAD_4B;
case SPI_NOR_CMD_2READ:
return SPI_NOR_CMD_2READ_4B;
case SPI_NOR_CMD_QREAD:
return SPI_NOR_CMD_QREAD_4B;
case SPI_NOR_CMD_4READ:
return SPI_NOR_CMD_4READ_4B;
default:
/* use provided */
return opcode;
}
}
static inline uint8_t spi_nor_convert_write_to_4b(const uint8_t opcode)
{
switch (opcode) {
case SPI_NOR_CMD_PP:
return SPI_NOR_CMD_PP_4B;
case SPI_NOR_CMD_PP_1_1_4:
return SPI_NOR_CMD_PP_1_1_4_4B;
case SPI_NOR_CMD_PP_1_4_4:
return SPI_NOR_CMD_PP_1_4_4_4B;
default:
/* use provided */
return opcode;
}
}
static int spi_nor_process_bfp(const struct device *dev,
const struct jesd216_param_header *php,
const struct jesd216_bfp *bfp)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *data = dev->data;
/* must be kept in data mode order, ignore 1-1-1 (always supported) */
const enum jesd216_mode_type supported_read_modes[] = { JESD216_MODE_112, JESD216_MODE_122,
JESD216_MODE_114,
JESD216_MODE_144 };
size_t supported_read_modes_max_idx;
struct jesd216_erase_type *etp = data->erase_types;
size_t idx;
const size_t flash_size = jesd216_bfp_density(bfp) / 8U;
struct jesd216_instr read_instr = { 0 };
struct jesd216_bfp_dw15 dw15;
if (flash_size != dev_cfg->flash_size) {
LOG_DBG("Unexpected flash size: %u", flash_size);
}
LOG_DBG("%s: %u MiBy flash", dev->name, (uint32_t)(flash_size >> 20));
/* Copy over the erase types, preserving their order. (The
* Sector Map Parameter table references them by index.)
*/
memset(data->erase_types, 0, sizeof(data->erase_types));
for (idx = 1U; idx <= ARRAY_SIZE(data->erase_types); ++idx) {
if (jesd216_bfp_erase(bfp, idx, etp) == 0) {
LOG_DBG("Erase %u with %02x",
(uint32_t)BIT(etp->exp), etp->cmd);
}
++etp;
}
spi_nor_process_bfp_addrbytes(dev, jesd216_bfp_addrbytes(bfp));
LOG_DBG("Address width: %u Bytes", data->address_width);
/* use PP opcode based on configured data mode if nothing is set in DTS */
if (data->write_opcode == SPI_NOR_WRITEOC_NONE) {
switch (dev_cfg->data_mode) {
case XSPI_OCTO_MODE:
data->write_opcode = SPI_NOR_OCMD_PAGE_PRG;
break;
case XSPI_QUAD_MODE:
data->write_opcode = SPI_NOR_CMD_PP_1_4_4;
break;
case XSPI_DUAL_MODE:
data->write_opcode = SPI_NOR_CMD_PP_1_1_2;
break;
default:
data->write_opcode = SPI_NOR_CMD_PP;
break;
}
}
if (dev_cfg->data_mode != XSPI_OCTO_MODE) {
/* determine supported read modes, begin from the slowest */
data->read_mode = JESD216_MODE_111;
data->read_opcode = SPI_NOR_CMD_READ;
data->read_dummy = 0U;
if (dev_cfg->data_mode != XSPI_SPI_MODE) {
if (dev_cfg->data_mode == XSPI_DUAL_MODE) {
/* the index of JESD216_MODE_114 in supported_read_modes */
supported_read_modes_max_idx = 2U;
} else {
supported_read_modes_max_idx = ARRAY_SIZE(supported_read_modes);
}
for (idx = 0U; idx < supported_read_modes_max_idx; ++idx) {
if (jesd216_bfp_read_support(php, bfp, supported_read_modes[idx],
&read_instr) < 0) {
/* not supported */
continue;
}
LOG_DBG("Supports read mode: %d, instr: 0x%X",
supported_read_modes[idx], read_instr.instr);
data->read_mode = supported_read_modes[idx];
data->read_opcode = read_instr.instr;
data->read_dummy =
(read_instr.wait_states + read_instr.mode_clocks);
}
}
/* convert 3-Byte opcodes to 4-Byte (if required) */
if (IS_ENABLED(DT_INST_PROP(0, four_byte_opcodes))) {
if (data->address_width != 4U) {
LOG_DBG("4-Byte opcodes require 4-Byte address width");
return -ENOTSUP;
}
data->read_opcode = spi_nor_convert_read_to_4b(data->read_opcode);
data->write_opcode = spi_nor_convert_write_to_4b(data->write_opcode);
}
/* enable quad mode (if required) */
if (dev_cfg->data_mode == XSPI_QUAD_MODE) {
if (jesd216_bfp_decode_dw15(php, bfp, &dw15) < 0) {
/* will use QER from DTS or default (refer to device data) */
LOG_WRN("Unable to decode QE requirement [DW15]");
} else {
/* bypass DTS QER value */
data->qer_type = dw15.qer;
}
LOG_DBG("QE requirement mode: %x", data->qer_type);
if (stm32_xspi_enable_qe(dev) < 0) {
LOG_ERR("Failed to enable QUAD mode");
return -EIO;
}
LOG_DBG("QUAD mode enabled");
}
}
data->page_size = jesd216_bfp_page_size(php, bfp);
LOG_DBG("Page size %u bytes", data->page_size);
LOG_DBG("Flash size %zu bytes", flash_size);
LOG_DBG("Using read mode: %d, instr: 0x%X, dummy cycles: %u",
data->read_mode, data->read_opcode, data->read_dummy);
LOG_DBG("Using write instr: 0x%X", data->write_opcode);
return 0;
}
#if STM32_XSPI_USE_DMA
static int flash_stm32_xspi_dma_init(DMA_HandleTypeDef *hdma, struct stream *dma_stream)
{
int ret;
/*
* DMA configuration
* Due to use of XSPI HAL API in current driver,
* both HAL and Zephyr DMA drivers should be configured.
* The required configuration for Zephyr DMA driver should only provide
* the minimum information to inform the DMA slot will be in used and
* how to route callbacks.
*/
if (!device_is_ready(dma_stream->dev)) {
LOG_ERR("DMA %s device not ready", dma_stream->dev->name);
return -ENODEV;
}
/* Proceed to the minimum Zephyr DMA driver init of the channel */
dma_stream->cfg.user_data = hdma;
/* HACK: This field is used to inform driver that it is overridden */
dma_stream->cfg.linked_channel = STM32_DMA_HAL_OVERRIDE;
/* Because of the STREAM OFFSET, the DMA channel given here is from 1 - 8 */
ret = dma_config(dma_stream->dev,
(dma_stream->channel + STM32_DMA_STREAM_OFFSET), &dma_stream->cfg);
if (ret != 0) {
LOG_ERR("Failed to configure DMA channel %d",
dma_stream->channel + STM32_DMA_STREAM_OFFSET);
return ret;
}
/* Proceed to the HAL DMA driver init */
if (dma_stream->cfg.source_data_size != dma_stream->cfg.dest_data_size) {
LOG_ERR("DMA Source and destination data sizes not aligned");
return -EINVAL;
}
hdma->Init.SrcDataWidth = DMA_SRC_DATAWIDTH_WORD; /* Fixed value */
hdma->Init.DestDataWidth = DMA_DEST_DATAWIDTH_WORD; /* Fixed value */
hdma->Init.SrcInc = (dma_stream->src_addr_increment)
? DMA_SINC_INCREMENTED
: DMA_SINC_FIXED;
hdma->Init.DestInc = (dma_stream->dst_addr_increment)
? DMA_DINC_INCREMENTED
: DMA_DINC_FIXED;
hdma->Init.SrcBurstLength = 4;
hdma->Init.DestBurstLength = 4;
hdma->Init.Priority = table_priority[dma_stream->cfg.channel_priority];
hdma->Init.Direction = table_direction[dma_stream->cfg.channel_direction];
hdma->Init.TransferAllocatedPort = DMA_SRC_ALLOCATED_PORT0 | DMA_SRC_ALLOCATED_PORT1;
hdma->Init.TransferEventMode = DMA_TCEM_BLOCK_TRANSFER;
hdma->Init.Mode = DMA_NORMAL;
hdma->Init.BlkHWRequest = DMA_BREQ_SINGLE_BURST;
hdma->Init.Request = dma_stream->cfg.dma_slot;
/*
* HAL expects a valid DMA channel (not DMAMUX).
* The channel is from 0 to 7 because of the STM32_DMA_STREAM_OFFSET
* in the dma_stm32 driver
*/
hdma->Instance = LL_DMA_GET_CHANNEL_INSTANCE(dma_stream->reg,
dma_stream->channel);
/* Initialize DMA HAL */
if (HAL_DMA_Init(hdma) != HAL_OK) {
LOG_ERR("XSPI DMA Init failed");
return -EIO;
}
if (HAL_DMA_ConfigChannelAttributes(hdma, DMA_CHANNEL_NPRIV) != HAL_OK) {
LOG_ERR("XSPI DMA Init failed");
return -EIO;
}
LOG_DBG("XSPI with DMA transfer");
return 0;
}
#endif /* STM32_XSPI_USE_DMA */
static int flash_stm32_xspi_init(const struct device *dev)
{
const struct flash_stm32_xspi_config *dev_cfg = dev->config;
struct flash_stm32_xspi_data *dev_data = dev->data;
uint32_t ahb_clock_freq;
uint32_t prescaler = STM32_XSPI_CLOCK_PRESCALER_MIN;
int ret;
/* The SPI/DTR is not a valid config of data_mode/data_rate according to the DTS */
if ((dev_cfg->data_mode != XSPI_OCTO_MODE)
&& (dev_cfg->data_rate == XSPI_DTR_TRANSFER)) {
/* already the right config, continue */
LOG_ERR("XSPI mode SPI|DUAL|QUAD/DTR is not valid");
return -ENOTSUP;
}
/* Signals configuration */
ret = pinctrl_apply_state(dev_cfg->pcfg, PINCTRL_STATE_DEFAULT);
if (ret < 0) {
LOG_ERR("XSPI pinctrl setup failed (%d)", ret);
return ret;
}
if (!device_is_ready(DEVICE_DT_GET(STM32_CLOCK_CONTROL_NODE))) {
LOG_ERR("clock control device not ready");
return -ENODEV;
}
#ifdef CONFIG_STM32_MEMMAP
/* If MemoryMapped then configure skip init */
if (stm32_xspi_is_memorymap(dev)) {
LOG_DBG("NOR init'd in MemMapped mode\n");
/* Force HAL instance in correct state */
dev_data->hxspi.State = HAL_XSPI_STATE_BUSY_MEM_MAPPED;
return 0;
}
#endif /* CONFIG_STM32_MEMMAP */
if (dev_cfg->pclk_len > 3) {
/* Max 3 domain clock are expected */
LOG_ERR("Could not select %d XSPI domain clock", dev_cfg->pclk_len);
return -EIO;
}
/* Clock configuration */
if (clock_control_on(DEVICE_DT_GET(STM32_CLOCK_CONTROL_NODE),
(clock_control_subsys_t) &dev_cfg->pclken[0]) != 0) {
LOG_ERR("Could not enable XSPI clock");
return -EIO;
}
if (clock_control_get_rate(DEVICE_DT_GET(STM32_CLOCK_CONTROL_NODE),
(clock_control_subsys_t) &dev_cfg->pclken[0],
&ahb_clock_freq) < 0) {
LOG_ERR("Failed call clock_control_get_rate(pclken)");
return -EIO;
}
/* Alternate clock config for peripheral if any */
if (IS_ENABLED(STM32_XSPI_DOMAIN_CLOCK_SUPPORT) && (dev_cfg->pclk_len > 1)) {
if (clock_control_configure(DEVICE_DT_GET(STM32_CLOCK_CONTROL_NODE),
(clock_control_subsys_t) &dev_cfg->pclken[1],
NULL) != 0) {
LOG_ERR("Could not select XSPI domain clock");
return -EIO;
}
/*
* Get the clock rate from this one (update ahb_clock_freq)
* TODO: retrieve index in the clocks property where clocks has "xspi-ker"
* Assuming index is 1
*/
if (clock_control_get_rate(DEVICE_DT_GET(STM32_CLOCK_CONTROL_NODE),
(clock_control_subsys_t) &dev_cfg->pclken[1],
&ahb_clock_freq) < 0) {
LOG_ERR("Failed call clock_control_get_rate(pclken)");
return -EIO;
}
}
/* Clock domain corresponding to the IO-Mgr (XSPIM) */
if (IS_ENABLED(STM32_XSPI_DOMAIN_CLOCK_SUPPORT) && (dev_cfg->pclk_len > 2)) {
if (clock_control_on(DEVICE_DT_GET(STM32_CLOCK_CONTROL_NODE),
(clock_control_subsys_t) &dev_cfg->pclken[2]) != 0) {
LOG_ERR("Could not enable XSPI Manager clock");
return -EIO;
}
/* Do NOT Get the clock rate from this one */
}
for (; prescaler <= STM32_XSPI_CLOCK_PRESCALER_MAX; prescaler++) {
uint32_t clk = STM32_XSPI_CLOCK_COMPUTE(ahb_clock_freq, prescaler);
if (clk <= dev_cfg->max_frequency) {
break;
}
}
__ASSERT_NO_MSG(prescaler >= STM32_XSPI_CLOCK_PRESCALER_MIN &&
prescaler <= STM32_XSPI_CLOCK_PRESCALER_MAX);
/* Initialize XSPI HAL structure completely */
dev_data->hxspi.Init.ClockPrescaler = prescaler;
/* The stm32 hal_xspi driver does not reduce DEVSIZE before writing the DCR1 */
dev_data->hxspi.Init.MemorySize = find_lsb_set(dev_cfg->flash_size) - 2;
#if defined(XSPI_DCR2_WRAPSIZE)
dev_data->hxspi.Init.WrapSize = HAL_XSPI_WRAP_NOT_SUPPORTED;
#endif /* XSPI_DCR2_WRAPSIZE */
/* STR mode else Macronix for DTR mode */
if (dev_cfg->data_rate == XSPI_DTR_TRANSFER) {
dev_data->hxspi.Init.MemoryType = HAL_XSPI_MEMTYPE_MACRONIX;
dev_data->hxspi.Init.DelayHoldQuarterCycle = HAL_XSPI_DHQC_ENABLE;
} else {
}
#if STM32_XSPI_DLYB_BYPASSED
dev_data->hxspi.Init.DelayBlockBypass = HAL_XSPI_DELAY_BLOCK_BYPASS;
#else
dev_data->hxspi.Init.DelayBlockBypass = HAL_XSPI_DELAY_BLOCK_ON;
#endif /* STM32_XSPI_DLYB_BYPASSED */
if (HAL_XSPI_Init(&dev_data->hxspi) != HAL_OK) {
LOG_ERR("XSPI Init failed");
return -EIO;
}
LOG_DBG("XSPI Init'd");
#if defined(HAL_XSPIM_IOPORT_1) || defined(HAL_XSPIM_IOPORT_2)
/* XSPI I/O manager init Function */
XSPIM_CfgTypeDef xspi_mgr_cfg;
if (dev_data->hxspi.Instance == XSPI1) {
xspi_mgr_cfg.IOPort = HAL_XSPIM_IOPORT_1;
} else if (dev_data->hxspi.Instance == XSPI2) {
xspi_mgr_cfg.IOPort = HAL_XSPIM_IOPORT_2;
}
xspi_mgr_cfg.nCSOverride = HAL_XSPI_CSSEL_OVR_DISABLED;
xspi_mgr_cfg.Req2AckTime = 1;
if (HAL_XSPIM_Config(&dev_data->hxspi, &xspi_mgr_cfg,
HAL_XSPI_TIMEOUT_DEFAULT_VALUE) != HAL_OK) {
LOG_ERR("XSPI M config failed");
return -EIO;
}
#endif /* XSPIM */
#if defined(DLYB_XSPI1) || defined(DLYB_XSPI2) || defined(DLYB_OCTOSPI1) || defined(DLYB_OCTOSPI2)
/* XSPI delay block init Function */
HAL_XSPI_DLYB_CfgTypeDef xspi_delay_block_cfg = {0};
(void)HAL_XSPI_DLYB_GetClockPeriod(&dev_data->hxspi, &xspi_delay_block_cfg);
/* with DTR, set the PhaseSel/4 (empiric value from stm32Cube) */
xspi_delay_block_cfg.PhaseSel /= 4;
if (HAL_XSPI_DLYB_SetConfig(&dev_data->hxspi, &xspi_delay_block_cfg) != HAL_OK) {
LOG_ERR("XSPI DelayBlock failed");
return -EIO;
}
LOG_DBG("Delay Block Init");
#endif /* DLYB_ */
#if STM32_XSPI_USE_DMA
/* Configure and enable the DMA channels after XSPI config */
static DMA_HandleTypeDef hdma_tx;
static DMA_HandleTypeDef hdma_rx;
if (flash_stm32_xspi_dma_init(&hdma_tx, &dev_data->dma_tx) != 0) {
LOG_ERR("XSPI DMA Tx init failed");
return -EIO;
}
/* The dma_tx handle is hold by the dma_stream.cfg.user_data */
__HAL_LINKDMA(&dev_data->hxspi, hdmatx, hdma_tx);
if (flash_stm32_xspi_dma_init(&hdma_rx, &dev_data->dma_rx) != 0) {
LOG_ERR("XSPI DMA Rx init failed");
return -EIO;
}
/* The dma_rx handle is hold by the dma_stream.cfg.user_data */
__HAL_LINKDMA(&dev_data->hxspi, hdmarx, hdma_rx);
#endif /* CONFIG_USE_STM32_HAL_DMA */
/* Initialize semaphores */
k_sem_init(&dev_data->sem, 1, 1);
k_sem_init(&dev_data->sync, 0, 1);
/* Run IRQ init */
dev_cfg->irq_config(dev);
/* Reset NOR flash memory : still with the SPI/STR config for the NOR */
if (stm32_xspi_mem_reset(dev) != 0) {
LOG_ERR("XSPI reset failed");
return -EIO;
}
LOG_DBG("Reset Mem (SPI/STR)");
/* Check if memory is ready in the SPI/STR mode */
if (stm32_xspi_mem_ready(dev,
XSPI_SPI_MODE, XSPI_STR_TRANSFER) != 0) {
LOG_ERR("XSPI memory not ready");
return -EIO;
}
LOG_DBG("Mem Ready (SPI/STR)");
#if defined(CONFIG_FLASH_JESD216_API)
/* Process with the RDID (jedec read ID) instruction at init and fill jedec_id Table */
ret = stm32_xspi_read_jedec_id(dev);
if (ret != 0) {
LOG_ERR("Read ID failed: %d", ret);
return ret;
}
#endif /* CONFIG_FLASH_JESD216_API */
if (stm32_xspi_config_mem(dev) != 0) {
LOG_ERR("OSPI mode not config'd (%u rate %u)",
dev_cfg->data_mode, dev_cfg->data_rate);
return -EIO;
}
/* Send the instruction to read the SFDP */
const uint8_t decl_nph = 2;
union {
/* We only process BFP so use one parameter block */
uint8_t raw[JESD216_SFDP_SIZE(decl_nph)];
struct jesd216_sfdp_header sfdp;
} u;
const struct jesd216_sfdp_header *hp = &u.sfdp;
ret = xspi_read_sfdp(dev, 0, u.raw, sizeof(u.raw));
if (ret != 0) {
LOG_ERR("SFDP read failed: %d", ret);
return ret;
}
uint32_t magic = jesd216_sfdp_magic(hp);
if (magic != JESD216_SFDP_MAGIC) {
LOG_ERR("SFDP magic %08x invalid", magic);
return -EINVAL;
}
LOG_DBG("%s: SFDP v %u.%u AP %x with %u PH", dev->name,
hp->rev_major, hp->rev_minor, hp->access, 1 + hp->nph);
const struct jesd216_param_header *php = hp->phdr;
const struct jesd216_param_header *phpe = php +
MIN(decl_nph, 1 + hp->nph);
while (php != phpe) {
uint16_t id = jesd216_param_id(php);
LOG_DBG("PH%u: %04x rev %u.%u: %u DW @ %x",
(php - hp->phdr), id, php->rev_major, php->rev_minor,
php->len_dw, jesd216_param_addr(php));
if (id == JESD216_SFDP_PARAM_ID_BFP) {
union {
uint32_t dw[20];
struct jesd216_bfp bfp;
} u2;
const struct jesd216_bfp *bfp = &u2.bfp;
ret = xspi_read_sfdp(dev, jesd216_param_addr(php),
(uint8_t *)u2.dw,
MIN(sizeof(uint32_t) * php->len_dw, sizeof(u2.dw)));
if (ret == 0) {
ret = spi_nor_process_bfp(dev, php, bfp);
}
if (ret != 0) {
LOG_ERR("SFDP BFP failed: %d", ret);
break;
}
}
if (id == JESD216_SFDP_PARAM_ID_4B_ADDR_INSTR) {
if (dev_data->address_width == 4U) {
/*
* Check table 4 byte address instruction table to get supported
* erase opcodes when running in 4 byte address mode
*/
union {
uint32_t dw[2];
struct {
uint32_t dummy;
uint8_t type[4];
} types;
} u2;
ret = xspi_read_sfdp(dev, jesd216_param_addr(php),
(uint8_t *)u2.dw,
MIN(sizeof(uint32_t) * php->len_dw, sizeof(u2.dw)));
if (ret != 0) {
break;
}
for (uint8_t ei = 0; ei < JESD216_NUM_ERASE_TYPES; ++ei) {
struct jesd216_erase_type *etp = &dev_data->erase_types[ei];
const uint8_t cmd = u2.types.type[ei];
/* 0xff means not supported */
if (cmd == 0xff) {
etp->exp = 0;
etp->cmd = 0;
} else {
etp->cmd = cmd;
};
}
}
}
++php;
}
#if defined(CONFIG_FLASH_PAGE_LAYOUT)
ret = setup_pages_layout(dev);
if (ret != 0) {
LOG_ERR("layout setup failed: %d", ret);
return -ENODEV;
}
#endif /* CONFIG_FLASH_PAGE_LAYOUT */
#ifdef CONFIG_STM32_MEMMAP
ret = stm32_xspi_set_memorymap(dev);
if (ret != 0) {
LOG_ERR("Failed to enable memory-mapped mode: %d", ret);
return ret;
}
LOG_INF("Memory-mapped NOR-flash at 0x%lx (0x%x bytes)",
(long)(STM32_XSPI_BASE_ADDRESS),
dev_cfg->flash_size);
#else
LOG_INF("NOR external-flash at 0x%lx (0x%x bytes)",
(long)(STM32_XSPI_BASE_ADDRESS),
dev_cfg->flash_size);
#endif /* CONFIG_STM32_MEMMAP*/
return 0;
}
#if STM32_XSPI_USE_DMA
#define DMA_CHANNEL_CONFIG(node, dir) \
DT_DMAS_CELL_BY_NAME(node, dir, channel_config)
#define XSPI_DMA_CHANNEL_INIT(node, dir, dir_cap, src_dev, dest_dev) \
.dev = DEVICE_DT_GET(DT_DMAS_CTLR(node)), \
.channel = DT_DMAS_CELL_BY_NAME(node, dir, channel), \
.reg = (DMA_TypeDef *)DT_REG_ADDR( \
DT_PHANDLE_BY_NAME(node, dmas, dir)), \
.cfg = { \
.dma_slot = DT_DMAS_CELL_BY_NAME(node, dir, slot), \
.channel_direction = STM32_DMA_CONFIG_DIRECTION( \
DMA_CHANNEL_CONFIG(node, dir)), \
.channel_priority = STM32_DMA_CONFIG_PRIORITY( \
DMA_CHANNEL_CONFIG(node, dir)), \
.dma_callback = xspi_dma_callback, \
}, \
.src_addr_increment = STM32_DMA_CONFIG_##src_dev##_ADDR_INC( \
DMA_CHANNEL_CONFIG(node, dir)), \
.dst_addr_increment = STM32_DMA_CONFIG_##dest_dev##_ADDR_INC( \
DMA_CHANNEL_CONFIG(node, dir)),
#define XSPI_DMA_CHANNEL(node, dir, DIR, src, dest) \
.dma_##dir = { \
COND_CODE_1(DT_DMAS_HAS_NAME(node, dir), \
(XSPI_DMA_CHANNEL_INIT(node, dir, DIR, src, dest)), \
(NULL)) \
},
#else
#define XSPI_DMA_CHANNEL(node, dir, DIR, src, dest)
#endif /* CONFIG_USE_STM32_HAL_DMA */
#define XSPI_FLASH_MODULE(drv_id, flash_id) \
(DT_DRV_INST(drv_id), xspi_nor_flash_##flash_id)
#define DT_WRITEOC_PROP_OR(inst, default_value) \
COND_CODE_1(DT_INST_NODE_HAS_PROP(inst, writeoc), \
(_CONCAT(SPI_NOR_CMD_, DT_STRING_TOKEN(DT_DRV_INST(inst), writeoc))), \
((default_value)))
#define DT_QER_PROP_OR(inst, default_value) \
COND_CODE_1(DT_INST_NODE_HAS_PROP(inst, quad_enable_requirements), \
(_CONCAT(JESD216_DW15_QER_VAL_, \
DT_STRING_TOKEN(DT_DRV_INST(inst), quad_enable_requirements))), \
((default_value)))
static void flash_stm32_xspi_irq_config_func(const struct device *dev);
static const struct stm32_pclken pclken[] = STM32_DT_CLOCKS(STM32_XSPI_NODE);
PINCTRL_DT_DEFINE(STM32_XSPI_NODE);
static const struct flash_stm32_xspi_config flash_stm32_xspi_cfg = {
.pclken = pclken,
.pclk_len = DT_NUM_CLOCKS(STM32_XSPI_NODE),
.irq_config = flash_stm32_xspi_irq_config_func,
.flash_size = DT_INST_REG_ADDR_BY_IDX(0, 1),
.max_frequency = DT_INST_PROP(0, ospi_max_frequency),
.data_mode = DT_INST_PROP(0, spi_bus_width), /* SPI or OPI */
.data_rate = DT_INST_PROP(0, data_rate), /* DTR or STR */
.pcfg = PINCTRL_DT_DEV_CONFIG_GET(STM32_XSPI_NODE),
#if STM32_XSPI_RESET_GPIO
.reset = GPIO_DT_SPEC_INST_GET(0, reset_gpios),
#endif /* STM32_XSPI_RESET_GPIO */
#if DT_NODE_HAS_PROP(DT_INST(0, st_stm32_ospi_nor), sfdp_bfp)
.sfdp_bfp = DT_INST_PROP(0, sfdp_bfp),
#endif /* sfdp_bfp */
};
static struct flash_stm32_xspi_data flash_stm32_xspi_dev_data = {
.hxspi = {
.Instance = (XSPI_TypeDef *)DT_REG_ADDR(STM32_XSPI_NODE),
.Init = {
.FifoThresholdByte = STM32_XSPI_FIFO_THRESHOLD,
.SampleShifting = (DT_PROP(STM32_XSPI_NODE, ssht_enable)
? HAL_XSPI_SAMPLE_SHIFT_HALFCYCLE
: HAL_XSPI_SAMPLE_SHIFT_NONE),
.ChipSelectHighTimeCycle = 1,
.ClockMode = HAL_XSPI_CLOCK_MODE_0,
.ChipSelectBoundary = 0,
.MemoryMode = HAL_XSPI_SINGLE_MEM,
#if defined(HAL_XSPIM_IOPORT_1) || defined(HAL_XSPIM_IOPORT_2)
.MemorySelect = ((DT_INST_PROP(0, ncs_line) == 1)
? HAL_XSPI_CSSEL_NCS1
: HAL_XSPI_CSSEL_NCS2),
#endif
.FreeRunningClock = HAL_XSPI_FREERUNCLK_DISABLE,
#if defined(OCTOSPI_DCR4_REFRESH)
.Refresh = 0,
#endif /* OCTOSPI_DCR4_REFRESH */
},
},
.qer_type = DT_QER_PROP_OR(0, JESD216_DW15_QER_VAL_S1B6),
.write_opcode = DT_WRITEOC_PROP_OR(0, SPI_NOR_WRITEOC_NONE),
.page_size = SPI_NOR_PAGE_SIZE, /* by default, to be updated by sfdp */
#if DT_NODE_HAS_PROP(DT_INST(0, st_stm32_ospi_nor), jedec_id)
.jedec_id = DT_INST_PROP(0, jedec_id),
#endif /* jedec_id */
XSPI_DMA_CHANNEL(STM32_XSPI_NODE, tx, TX, MEMORY, PERIPHERAL)
XSPI_DMA_CHANNEL(STM32_XSPI_NODE, rx, RX, PERIPHERAL, MEMORY)
};
static void flash_stm32_xspi_irq_config_func(const struct device *dev)
{
IRQ_CONNECT(DT_IRQN(STM32_XSPI_NODE), DT_IRQ(STM32_XSPI_NODE, priority),
flash_stm32_xspi_isr, DEVICE_DT_INST_GET(0), 0);
irq_enable(DT_IRQN(STM32_XSPI_NODE));
}
DEVICE_DT_INST_DEFINE(0, &flash_stm32_xspi_init, NULL,
&flash_stm32_xspi_dev_data, &flash_stm32_xspi_cfg,
POST_KERNEL, CONFIG_KERNEL_INIT_PRIORITY_DEVICE,
&flash_stm32_xspi_driver_api);